Jump to content
SAU Community

Recommended Posts

Currently looking to upgrade the turbo on the R33, as I already have the SAFC I was wondering if only tuning fuel and not timing would be a major issue with the new turbo? The far off goal is really only 250rwkw eventially with a PFC, but for know the budget will only allow the turbo, I already have a pump, FMIC etc... so I'm aiming for maybe 230rwkw for now, could it be done with the stock AFM and injectors or otherwise I could stretch the budget and get the Z32 AFM and I was thinking S15 injectors would be a cheaper option. So yeah opinions are welcomed but feedback from people who have been there and done that would be appreciated too, thanks.

Unfortunately as you are probably aware, the fuel/ignition relationship doesn't work very well, with a fuel bender and is defiantely the limiting factor in the power made. I wouldnt push the setup too hard, and consider the SAFC a bandaid which really needs to be fixed to get the most out of the supporting mods. Maybe have a look at the Greddy emanage Ultimate as another option, as its not as $$$$ as PFC's are getting

SAFC + SITC + Z32afm + Nismo FPR isnt too bad an option, as far as bandaid measures go

200rwkw from an auto is definately doable, so add a few rwkw more on for a manual

Ive got Deatschwerks 550cc injectors waiting to go in, but will be doing the remap option (in lieu of aftermarket ecu) when it comes time to put in the injectors, boost her up a little more, and tune (will keep the piggybacks for extra tuneability, I reckon).

I got 230rwkw out of my rb20 with an safc2, runs fine with good tuned afrs (its posted rb20 performace thread), I still get 500kms to a tank. Although im getting a remap and z32 though as the afm maxes out slightly on cold days. I think throwing some good timing in will sort out the small compresssor surge i get when slowly ramping up boost under load and the other advantages of more power quicker spool up etc..I have gtr injectors also.

so if i was to run a safc2+sitc would getting an r33 ecu remap aswell be advantageous?

they are a fair bit pricey though arent they? i would guess the costs of a remap would out weigh the benefits.

i ask because i am about to install safc2+sitc and run with standard turbo+injectors+afm and aim for around 200rwkw

then upgrade turbo and injectors for 250ish rwkw at this point ill probably need better management, perhaps an ecu remap.

i already have other supporting mods etc

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...