Jump to content
SAU Community

Hi Flow Race/street Performance Cat 3"

bazr33

By bazr33,
in Classifieds

 Share

Recommended Posts

bazr33 Mentor

bazr33

Posted
Posted (edited)

post-14294-1208161934_thumb.jpgpost-14294-1208161895_thumb.jpg

STAINLESS STEEL HIGH PERFORMANCE RACE/STREET

CATALYTIC CONVERTER 3" HI-FLOW NEW

New Top Quality High Flow Ceramic Universal Catalytic Converter.

This has 3"ends 11" long and 4" round Universal OBD II compliant.

Don't let your stock converter slow you down. If your looking to open up your exhaust flow and get some free Horsepower, this Cat is for you.

This converter is one of the BEST in the Industry, it is made from T-409 Stainless Steel - Won't Rust, can be polished, can be slip fitted, or welded, are compact and light weight, and out flow most other aftermarket converters.

This high flow converter features a ceramic brick with 300 holes per square inch.

Offering better Performance and Flow, in some cases more than 50%, than comparable converters, and sometimes costing hundreds less...

The end veiw picture shows a standard flash light shining through the core, that's free flow capability.

Also dissipates heat better due to there design.

Don't be fooled by some other lower priced, welded together units, or some second rate knock off, these are OBD II compliant.

Length - 11"

Body - 4" Round

Inlet - 3"

Outlet - 3"

Brick Type - Ceramic

Price $200 negiotable

Edited by bazr33
bazr33 Mentor

bazr33

Posted
  • Author
Posted

i am finding out the information for the above questions at the moment.

I am unaware of flow and brand, as i only wanted it cause my old cat was hitting the floor of my car.

As i found out the old cat was only hitting by mm's i just put a dent in the floor and now it misses.

I have pulled the cat out of the box and it looks of high standard quality.

bazr33 Mentor

bazr33

Posted
  • Author
Posted

Hey Zennon

The brand name is Thunderbolt they are an American Hi flow converter.

I do not have the flow rate.

I do have the CPI(cells per sq. inch).

The ceramics are 330cpi

Thanks

ZENNON Grand Master

ZENNON

Posted
Posted
The brand name is Thunderbolt they are an American Hi flow converter.

Sure?

Thunderbolt: http://www.performance-curve.com/index.asp...amp;ProdID=1172

Other: http://www.performance-curve.com/index.asp...amp;ProdID=1060

GL with sale anyway

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...