Jump to content
SAU Community

Recommended Posts

Since pod filters are illegal unless enclosed, how would a good panel filter (such as K&N) compare with a pod? I can't see the panel filter allowing anywhere near as much airflow.

Also, should I just go ahead and put a pod filter in my '89 celica? It's not like I'm gonna get pulled over and inspected right?

Link to comment
https://www.sau.com.au/forums/topic/21672-pod-vs-panel-filter/
Share on other sites

Good panel filters, K&N, redline and the likes are very close to as good as a pod.

i persoanlly prefer a pod cause of the noise which some think is too ricey.

dont really know squat about celicas turbo or not buy if its not turbo it wont make a noise and wont attract the cops as much, i had a pod on my old NA car and it didnt make a noise so you should be sweet

yer cold air #1....

u can get proper boxed made for the pods unique autosports have them but obviously they would cost a bit but id say it would be better than a pannel, i got a cover round mine mainly just a temprary one i used out of heat proof aluminium jus to pass my defect, only cost me 15 bucks to do untill i get the money for a carbon air box

cheers....

www.freewebs.com/2BNVS_r33

honestly, how can you seriously measure a device like this on a dyno. Is a dyno fan providing anything like normal airflow. How many of you drive around with the bonnet up?

personally, I have to go for the pod because the stock box won't work with a fmic... otherwise, it would be a panel all the way - hopefully with an aftermarket induction setup (or a ghetto DIY setup at worst).

Originally posted by Jimbo2000

so are the UAS ones legal?

i am thinking of getting one.

another workshop near there make a SERIOUS one for like 500

I'm pretty sure they're legal, I've never seen an air box which has some sort of ADR approval stamp or sticker on it like brake lines for example.

The other workshop wouldn't be Hills Motorsports would it? ;) Their box is made from aluminium and seals better than the UAS one. At the cost you mentioned though it's really only worthwhile if you have lots of money to burn. I got the cheaper fibreglass one from UAS for around $160 I think. It does the job well enough.

This whole air-filter business is really quite amusing.

Normal atmospheric pressure is around 410 inches of water gauge pressure, so if your stock air filter has say 4 inches of water pressure drop at full power, you are seeing (406/410) or 99% atmospheric pressure after the air-filter.

So you fit some monstrous expensive aftermarket air filter box or pod, that is advertised as having guaranteed TWICE the airflow of the stock filter. So you fit it, and sure enough there is now only two inches of water pressure drop at full power. There is now 408/410) or 99.5% atmospheric pressure. So expect an 0.5% power gain.

A far more important consideration is air temperature. Air density works from absolute temperature (the Kelvin scale). To convert Celsius to Kelvin you add 273. So 27C equals 300K.

So for every three degrees of temperature rise, you loose one percent in air density, which equates to roughly one percent power.

So your new super air filter has about the same effect on power as lowering the intake air temperature about 1.5 degrees.

So use whatever type of air-filter you want, or is convenient, and concentrate on getting the coldest possible inlet air. There are far greater gains to be had that way.

But a lot of guys prefer a brightly coloured chrome pod right behind the radiator, because it looks nice when you open the bonnet.

On the other hand a stock air-box with partially concealed cold air pickup behind the front bumper, will probably work far better and keep the cops happy as well.

I ran mine on the dyno when it was making 164rwkw with a pod and with the stock air box & stock new filter.

They both made exactly the same power.

Both were run with the bonnet open.

Since then I've modded my standard airbox. It now has a 100mm CAI using PVC piping with a 45degree bend that enters the air box where the standard small arsed cai was. I've grabbed my self some plastic and a bit of superglue & silicon to old it all to get her and make it look flush. Pop the bonnet and it looks stock. Everything is black and unless you really know something about skylines you wouldn't pick it.

It has made the bov and induction/turbo whistle heaps louder.

It should now be ok for the 450-500hp that I am chasing :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...