Jump to content
SAU Community

Recommended Posts

I am in a spot of bother!

my immobiliser in my commonwhore is ****ed, i tried to override it with the pin but with no luck

i was wondering if anyone in this forum knows how to disconnect an immobiliser so i can at least drive my car and get another one fitted

any advice or help would be greatly appreciated

its a cyclops unit if that helps

Link to comment
https://www.sau.com.au/forums/topic/22107-disconnecting-immobiliser/
Share on other sites

With a dynatron/cyclops brand it's pretty easy, but involves re-wiring under the dash. Usually they cut off BOTH ignition wires with relays...

You'll see something like this:

Car Ign+ --> Relay --> Wiring harness

Car Ign- --> Relay --> Wiring harness

|

|

Immobiliser Unit

Connect the Ign+, and Ign-, back into the wiring harness, bypassing the relays.. May take some rooting around, but it's not impossible...

Hope that helps :P

usually immob are in series with 2 circuits under the dash - u should be able to see where ignition wires (thick) have been cut and the immob wires (thin) soldered in series with them

desolder the immob wires and just connect the original wiring back together

speaking of vk's there are too many similar shitheaps thrashing around the streets of warwick - i know coz i live there ;)

here is an easier option.. usually works easier if you have a manual though...

If you have a 'cheaper' varient of the cyclone immobilisers, then this should get ya going.. turn the ignition to 'on' and leave the car there for approximately 35-50 minutes, if you have an electric fan, disconnect it, unless you have a manual which you can push start when your battery dies. Thats why this is easier with a manual. Go to the car after 40ish minutes and try turn the key, if it doesnt work, wait another 20 mins, if that doesnt work.. then im stumped ;) you have to go cutting :)

I KNOW and have seen this work to alot of cars, this works on stock vt commos as well.

Originally posted by NuGGeT

hmm its amazing if you can disconnect your own immobiliser imagine what car theives can do?!!? hahha thats scary if people on this forum can tell u how to get rid of ya immobiliser

hahaha

to get rid of your alarm, all you do, is lie down under the bonnet, reach up, pull the bonnet cable, bonnet pops up, alarm goes mental, rip the siren out.. and then the alarm is useless :)

Originally posted by hako

speaking of vk's there are too many similar shitheaps thrashing around the streets of warwick - i know coz i live there :D

mate my car ain't a shitheap

although it ain't a skyline it is good for the money i paid

i managed to find a way to trip the alarm so i could use my car. :thumbsup:

now to get down to business and work out a budget so i can get my R32 GTR.....better be ready ONYX

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, plenty of air flow, there is a dedicated path that feeds the air in to the OEM intake tube behind the bumper As for a "tangible effect", maybe, but getting the pod/intake air out of the hot engine bay is worth it psychologically to me, even if it gives no performance difference, so the tangible effect in my Lizard brain saysss yessss  In the end, to me a tangible effect isn't always about performance, sometimes it a sound or a look, or even a...... feeling  Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga
    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
×
×
  • Create New...