Jump to content
SAU Community

Recommended Posts

I am in a spot of bother!

my immobiliser in my commonwhore is ****ed, i tried to override it with the pin but with no luck

i was wondering if anyone in this forum knows how to disconnect an immobiliser so i can at least drive my car and get another one fitted

any advice or help would be greatly appreciated

its a cyclops unit if that helps

Link to comment
https://www.sau.com.au/forums/topic/22107-disconnecting-immobiliser/
Share on other sites

With a dynatron/cyclops brand it's pretty easy, but involves re-wiring under the dash. Usually they cut off BOTH ignition wires with relays...

You'll see something like this:

Car Ign+ --> Relay --> Wiring harness

Car Ign- --> Relay --> Wiring harness

|

|

Immobiliser Unit

Connect the Ign+, and Ign-, back into the wiring harness, bypassing the relays.. May take some rooting around, but it's not impossible...

Hope that helps :P

usually immob are in series with 2 circuits under the dash - u should be able to see where ignition wires (thick) have been cut and the immob wires (thin) soldered in series with them

desolder the immob wires and just connect the original wiring back together

speaking of vk's there are too many similar shitheaps thrashing around the streets of warwick - i know coz i live there ;)

here is an easier option.. usually works easier if you have a manual though...

If you have a 'cheaper' varient of the cyclone immobilisers, then this should get ya going.. turn the ignition to 'on' and leave the car there for approximately 35-50 minutes, if you have an electric fan, disconnect it, unless you have a manual which you can push start when your battery dies. Thats why this is easier with a manual. Go to the car after 40ish minutes and try turn the key, if it doesnt work, wait another 20 mins, if that doesnt work.. then im stumped ;) you have to go cutting :)

I KNOW and have seen this work to alot of cars, this works on stock vt commos as well.

Originally posted by NuGGeT

hmm its amazing if you can disconnect your own immobiliser imagine what car theives can do?!!? hahha thats scary if people on this forum can tell u how to get rid of ya immobiliser

hahaha

to get rid of your alarm, all you do, is lie down under the bonnet, reach up, pull the bonnet cable, bonnet pops up, alarm goes mental, rip the siren out.. and then the alarm is useless :)

Originally posted by hako

speaking of vk's there are too many similar shitheaps thrashing around the streets of warwick - i know coz i live there :D

mate my car ain't a shitheap

although it ain't a skyline it is good for the money i paid

i managed to find a way to trip the alarm so i could use my car. :thumbsup:

now to get down to business and work out a budget so i can get my R32 GTR.....better be ready ONYX

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...