Jump to content
SAU Community

Massive Shed Clean Out

Drifterdan

By Drifterdan,
in Tasmania

 Share

Recommended Posts

Drifterdan Collaborator

Drifterdan

Posted
Posted (edited)

Hey guys, I have the following for sale:

NISSAN:

-RB20 stock cooler - $20 good for tight arse NA to turbo conversions

-2 sets of r31 28 spline axels with new bearings and seals - $100 a pair - seals and bearings aren't cheap :happy:

-s13 rubber gearbox boot that goes over the trans tunnel under the leather interior one - $15

-rb20 and a rb30 throttle body - free lol

- Dr drift chipped "E5" SR20DET ecu $400 cost $470

- Brand new r31 rear discs - $130 - heaps cheaper than retail!!

-rb30 starter motor, pretty sure its a turbo one (will fit r33 gts-t in other words) but the number printed on it is: 9000 064 001 92027179 BOSCH $80 - rare to find

- r31 rear suspension arms with nolathane(or whatever its called lol) bushes.. one bush is a bit worn so I'll sell these for $90 which is cheap as the lower arms are brand spanking new

DSC00035.jpg

DSC00034.jpg

- HR31 front calipers - $30

- Random bearing lol, part number koyo RCT4067L1, pretty sure its for your average nissan, brand new $20

DSC00037.jpg

- rb20 alternator belt, part number 5PK0940 370KS brand new $20

- Random wastegate (R34 gt-t???) Number on it is: ASN 79

DSC00039.jpg

- Another random wastegate (s13 sr20 - I "think") - Number on it is: ****19-217 05155 17973

DSC00040.jpg

TOYOTA:

- 1jzgte minus turbos and sump, $1000ono

- ems stinger ecu, cable, wiring loom to suit the 1jz and coil packs + tuning cd, $1000 - retails for $1200 plus the cost of a tune, the igniters etc and you get it all ready to go on a stock engine with exhaust etc....

- Brand new Gt35r .86 housing also is silver ceramic coating $1900

- Brand new SARD 650cc injectors, $700

- Gates 1jz timing belt $95 SOLD at this stage...

- JZA70 manual brake pedal $30

- 2jz NA dizzy, head and NA manifolds/injectors - OFFERS

- Near new MX83 Cressida radiator $80

- Factory 1jz intercooler - wicked for NA to turbo conversions as they flow very well $50

- MX83 Grande LSD, still spins a solid 2 wheels and the centre was brand new 3 years ago. No whines or any of that crap. $250

- standard 1jz coils

- standard 1jz airbox

- R154 5th gear synchro - brand new! - I'll have to check up on how much this is worth :D There are 2 or 3 different synchros that fit a R154. Pretty confident this one will NOT fit a jzx70

DSC00038.jpg

RANDOM STUFF:

- Brand new SABER Smokey Air/Fuel and Water gauges, $120 ono each

- Battery box, suit middle sized battery - $50

- AU falcon radiator - 40,000kms - $70

- Random stereo splitter block, takes large battery sized cable for amps and the like -$50

DSC00041.jpg

Edited by Smooth
Link to comment
https://www.sau.com.au/forums/topic/222530-massive-shed-clean-out/
Share on other sites
  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...