Jump to content
SAU Community

Room To Rent In Launceston

ardie

By ardie,
in Tasmania

 Share

Recommended Posts

ardie Experienced

ardie

Posted
Posted

Well one for my housemates is moving back to Longford due to work commitments so we now have vacancy in our house coming up.

It’s a 3 bedroom, 2 bathroom (1 ensuite), all whitegoods included with most importantly a double lockup garage and 2 carports (have had 6 cars parked at the house without needing to use on street parking or park on the lawn, but there is plenty of on street parking as well. Rent is $90 and power is on pay as you go so we can work that out. Give me a call on 0415 658 595 if you’re interested, fat chicks need not apply, applicants with force induction will be looked upon favourably however it is not a pre requisite, and no vtec yo!

Well one for my housemates is moving back to Longford due to work commitments so we now have vacancy in our house coming up.

It’s a 3 bedroom, 2 bathroom (1 ensuite), all whitegoods included with most importantly a double lockup garage and 2 carports (have had 6 cars parked at the house without needing to use on street parking or park on the lawn, but there is plenty of on street parking as well. Rent is $90 and power is on pay as you go so we can work that out. Give me a call on 0415 658 595 if you’re interested, fat chicks need not apply, applicants with force induction will be looked upon favourably however it is not a pre requisite, and no vtec yo!

Link to comment
https://www.sau.com.au/forums/topic/224622-room-to-rent-in-launceston/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • PranK
      2001 R34DE

      By PranK · Posted

      R34DE as in R34 with an RB25DE? So did you get this? Or you planning to?  I'm not really sure what you're saying. 
    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
×
×
  • Create New...