Jump to content
SAU Community

Recommended Posts

So I've been having some battery problems lately and i'm assuming it was brought on by my 2 new amps, subwoofers and all my new speakers....

So my problem is basically that my battery doesnt seem to be charging fast enough and/or provide enough juice to crank up my car after a short drive.

I got my battery and my alternator tested and was told that my alternator is sending just over enough current to the battery to get it charged at full load (a/c on, lights, music playing etc.) and the battery was also tested to be working(although i doubt that it's doing too well)

So my conclusion was that the battery just isnt holding up to the task and was looking at getting an optima yellowtop or maybe even a redtop if someone recommends that.

After looking at the optima website i realized that there are different sizes and they make a huge difference in weight and obviously have different power specifications.

I was looking at one of the smaller ones, the D51. Would this be sufficient for my needs? I'm not looking to run a HUGE stereo system for hours on end with the engine off. I just want to be able to drive along with my music on and not worry about wether or not the car will start the next time i try it.

Sorry for the long post, but i'd really appreciate the help.

This is what my current sound system consists of btw:

2 x JL audio 12" subs

JL 500/1 Mono amp

JL 300/4 amp

Alpine Type R 6.5" components

Alpine Type R 6x9's

I have a red top, could not be happier, only problem was that i had to trim off the little yabs at the bottom so it fitted in the factory location in my 33.

i believe mine is 1000cca, and turns it over dam fast so im assuming it will be more than enough, but the first thing you should be looking into is your alternator, when the car is running it is running off the alternator, should not be running off the battery at all, if the battery is going dead whilst you are driving you need to get a bigger alternator first.

how would i check that?

but i kinda doubt it, since most of the time when it happens the car can barely turn over for 3-5 seconds.... so it'd have to be taking up a HELL of a lotta current if the battery wasnt the problem

i have a yellow top and had to custom fit it into the existing location. i'm very happy with its performance until recently after not driving it for a week it died on me again. I decided that I'd install a kill switch between the battery and the fuse holder for all my amps so that when I know i wont be driving it for long periods i can take the switch out easily. Also this means people who have my car eg mechanic etc can't see what my system can handle as it wont work for them :laugh: Since installing the switch I've never had a problem again with the battery or any of the above posts mentioned problems. There's more on the optima stuff here: http://www.skylinesaustralia.com/forums/Au....html&st=40 page 3 near the bottom includes a pic of my battery install job.

cheers, shane

I'm running 4 gauge cable from the battery through a kill swith that i picked up from Jaycar for about $15bucks or so, then to a fuse box holder that holds four massive glass 60amp fuses. from the fuse box 3 cables run to each of my 3 amps and 1 cable off to the computer. no kill switch in, no nothing! and battery hasn't had a problem since. i even left the car for 3 weeks without clicking it over but it still turned no problems. dude...do it!

which red tops are you guys running?

i'm looking at these 2

http://cgi.ebay.com/ebaymotors/Optima-Batt...sspagenameZWD1V

http://cgi.ebay.com/ebaymotors/Optima-9002...sspagenameZWDVW

and shanus, that sounds pretty cool, i might look into it.

so basically when do you hit the switch? when you park the car for a long time? wouldnt it be easyer to put a kill switch at the - wire for the battery?

Edited by MoogLe

huh? at the wire for the battery? not sure i follow

I have a number of massive cables coming direct off my yellow top optima battery.

1 of them goes to the original skyline stuff and fuse boxes and whatever,

1 I added on goes to my power converters for my screens,

and 1 I added also goes to this fuse box i was trying to explain. so yes, the kill switch is right near the battery in the boot.

Whenever I leave my car in the garage or at my parents for a long period of time I pull the switch out and leave it. I haven't needed to yet, but if i was ever going to drop my car off with someone i could so the same. otherwise it's cleaverly consealed behind one of my monitors in the boot that you reach around the back of to pull out push in, easy.

hope this helps. are you in melb? any cruises coming up soon i'd be happy to catch up...

cheers, Shane

I believe mine is the second one but it does not have the tabs on each end that i had to cut off.

so basically when do you hit the switch? when you park the car for a long time? wouldnt it be easyer to put a kill switch at the - wire for the battery?
huh? at the wire for the battery? not sure i follow

I think he means just disconnect the battery all together, the problem with that is that you will have to reprogram your head unit and clock every time you start it again.

yes, that's what i meant, putting the kill switch at the negative cable, thus disconnecting the battery

reason i say that is because i wouldn't think that the amp would be the only thing that would possibly pull current from the battery over a long period....

one thing i wanted to ask... i have both my amps negative cables running directly to the battery. is that a big problem? could that be contributing to the issue?

And shanus, i'm about a 20 hour flight away from melbourne lol, dont think we'll be bumping into each other any time soon :(

Edited by MoogLe

lol fair enough

umm it's probably best to get a multimeter across your equipment to see whats going on and whats draining it the most. I haven't run the negative cables back to the battery directly from my amps as i've installed an earth block and all my negatives run back to this grounding unit which goes to the battery or chassis i can't remember which one. usually it's recommended to do what you have done, so i can't see how it's a problem, as long as you use the same gauge wire for positive and negative.

here's a shocking photo of some of the crap going on with my boot before i cleaned it all up. i now have office style condue keeping everything in line and power away from other wires etc it's really quite a neat job now :) You may notice how I've had to customise the battery tray and use the angle grinder to take off the original lips on the side, then just used a wider plastic base under the optima battery - geez it's tight! The three fuse boxes are all run back to the battery seperately, the one i mentioned in previous posts is the one in the middle, which has the kill switch now installed. and finally, just underneath this is where all my negative cables are.

If you can't find a solution by installing a kill switch, perhaps test it all and use some ideas from people on here. have you got two seperate positive cables to each amp, or do they go through a fuse box similar to mine? perhaps that's another idea you can steal if you have no luck...

sorry bout the long post, shanus

post-44524-1216252002_thumb.jpg

ive got seperate pos cables to each amp.

yea i would love to find out what may or may not be pulling electricity all the time but i dont have a multimeter.

i'm pretty damn sure it's my battery acting up though, biggest reason is because a couple of months ago my car was garaged for like 2 months because i had to work on my turbo manifold and i didnt disconnect the battery.

when i went to start it up, it was COMPLETELY dead, couldnt even turn on the brake lights.

After that, there was another time my car stood for 2-3 days after which the battery was dead once again....

and i noticed that it seemed to be going down hill from there...

the wierd thing is that Napa tested the battery and said that it's fine.... i'm thinking that maybe it's still producing the right amount of current but just wont charge beyond a certain level. Is that possible? Or is what i'm thinking flawed?

nah its not flawed, i was thinking on the same path when i decided to get a new battery. i didn't know why it just kept getting worse and worse, to a point where i brought a brand new battery and again, it died! i stuffed around a little and my mechanic told me it was my interior aftermarket light drawing current constantly so i got rid of it but it kept happening. rather than stuffing around anymore i just went that little bit further to get an optima battery.

'they say' whoever 'they' are, that unlike acid batteries that once flattened will half their life, then flattened again another limb gone etc etc until they're screwed, optima batteries are built to last a flattening. in fact, they strive off that stuff, as long as they get a full charge again when flat! IMO go the optima, you wont regret it!

never officially found out, but i'm 100% sure it were my amps and equipment as I've never had a problem since installing the switch so it can't be anything else!

split systems aren't too bad either, (you mean running 2 batteries?) but then theres housing the other battery and getting it going, and the problem is you still have acid batteries! its up to you man, good luck with the set up and make sure you post pictures when it's all in!!!

but didnt you say that you never actually flipped the switch yet?

so how could that have helped if you never actually used it yet?

on a side note, i had to jump start the car AGAIN just a few minutes ago, GOD is this annoying!

cant wait to get my new battery in, gonna order it by this weekend so it'll be here when i get back from my 2 week vacation

Edited by MoogLe

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...