Jump to content
SAU Community

Do All Power Windows Stop Working Or What?

StOjA32

By StOjA32,
in Exterior & Interior Styling

 Share

Recommended Posts

StOjA32 Enthusiast

StOjA32

Posted
Posted

Hey guys .. is it just fact that all power windows will sotp working after a while .. my R32 GTST, the windows were perfect now the left side one only works when controlled by the drivers side switch .. drivers side window needs to be played with to get it working...

My real question is ... is it just a simple problem where the connection on the swtch is just old causing them not to work. is it easy to fix? can it be done on your own ?

could anyone help?

QWK32 Veteran

QWK32

Posted
Posted

first thing is check the switches are plugged in properly. with the 32 the major problem with windows not working properly is the Power Window Relay, which is located under the driverside doorcard to the rear of the door. a small black rectanglular box. they are easy to swap over and only cost around $20-$30 from the wreakers for a working one.

partyboy73 Rising Star

partyboy73

Posted
Posted

If the drivers window is the problem then its an easy soldering job on the relay box, most likely, and there is a thread on it in the DIY section. With the other windows only working from the master control, its just the contacts in the individual switches and is as easy as pulling them out, then carefully apart, and just clean up the contacts with some fine sandpaper. Mine were dirty as and now no probs, just be careful not to lose any of the little parts and take note of how it was together for reassembly. :thumbsup:

G3TFKD Proficient

G3TFKD

Posted
Posted

how about if the drivers side power windows works when it goes up, but doesn't always work to go down. would that be the relay or would that be the actual switch?

play around for a little bit and then the window goes down

p.s sorry for hi-jacking the thread

partyboy73 Rising Star

partyboy73

Posted
Posted
how about if the drivers side power windows works when it goes up, but doesn't always work to go down. would that be the relay or would that be the actual switch?

play around for a little bit and then the window goes down

p.s sorry for hi-jacking the thread

Thats what one of my rear switches was doing (4 door) so if its always going up, and is playin up going down, then its the contacts in the switch itself... only problem there is the master switch on the drivers side looks to be stuck together pretty good (was when I looked at it, then gave up. Turned out to be the relay anyway) Try carefully getting into the master switch and clean the contacts. I'm confident this will cure your problem.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      R32 GTST - 600KW+ RB28/CD009 Build

      By Dose Pipe Sutututu · Posted

      LOL.... a good amount of people (not all) on that continent seem to know everything and like to measure things in bananas, football fields, statue of liberties instead of the metric system lol.
    • dawhitehonky
      M35 Aftermarket Fuel Pump

      By dawhitehonky · Posted

      I assume the modules are similar enough, so if you've had no issues I don't see why I would. I have tried to find a wiring diagram for the FPCM / fuel pump circuit, but I can't find it anywhere. Otherwise, I would just do some wire cutting and joining at the FPCM and give the 12 V supplied to the FPCM directly to the pump instead. If you know anyone that could help with wiring diagrams, I'd be very happy  
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      If it dies, then bypass. The task isn't difficult. I have one running on a standard R32 FPCM. That's after nearly 20 years of it running an 040, which pull substantially more current than the Walbro. They're not the same module, but I'd hope it indicates that the R33 one should be man enough for the job. I think people kill them when putting proper sized pumps on them, not these little toy pumps we're talking about here.
    • GTSBoy
      Rapid-fire squeaking/creaking from rear suspension

      By GTSBoy · Posted

      Silicone spray won't hurt anything. And if it does, that's an opportunity to put some solid steel spherical bushings in, so you can really learn what suspension noise sounds like, If you're going to try it, just spray one bush at a time, so you can work out which one is actually noisy. My best guess is that if the noise started only since putting the coilovers in, then it is just noise being transmitted up through the top mounts of the struts, and not necessarily "new" noise from bushes. But it's almost impossible to know.
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Are you saying the 34 is SUV height, and not that we're talking about an SUV here? (because if we're talking about an SUV, you don't fix them. You just replace them when something breaks. Not worth establishing sufficient emotional connection with an SUV to warrant doing any work on one). I wouldn't jack my car up on a short little loop of 10mm steel rod poking out through a hole in the bumper bar, front or rear end. I realise that we're probably not talking about that type of loop at the front, being the one under/behind the bar on a Skyline.... but even for that one, trying to jack up on what amounts to a thin piece of steel, designed purely for withstanding a horizontal tension force, not a vertical compressive force (and so would be prone to buckling/crushing) and, my most particular bitch about it - located RIGHT AT THE EXTREME FRONT OF THE CAR, applying a load up through the radiator support panel, etc, with almost the entire mass of the car cantilevered between there and the rear wheels? Nope. Not doing that. Not on the regular. That structure out there in front of the front crossmember is not designed to carry load in the vertical direction. Not really designed to carry any load at all, really. The chassis rail that the tow point is connected to would be fine loaded in tension, as per towing. Not intended to carry the mass of the whole car, especially loaded all on one rail, with twisting and all sorts of shitty load distribution going on. No, I will happily drive up on some pieces of wood, thanks. That can only happen on driven wheels, and they are at the other end of the car, and this problem does not exist at that end of the car. And even then, I have been known to drive up on at least 1x piece of 2x8 each side at the rear, simply to reduce the amount of jack pumping necessary to get the car up high enough for the jack stands. What really really shits me about Skylines is the lack of decent places for chassis stands at either end of the car. You'd think they'd be designed into the crossmembers.
×
×
  • Create New...