Jump to content
SAU Community

Recommended Posts

Hey all,

just before the keyboard warriors start flaming, yes I have searched.

I have just gone to hell with my car. some of you might know that I have been trying to locate my stuttering problem for some time now.

I have just recently cleaned my AAC unit. changed back to hks pod filters. new spark plugs.

when i turned the car back on after being batery-less for about a week, the car went fine for around 10mins. The only thing that was weird in its good condition was that it was booting WAY to high, way above the stock boost, and i could hear the turbos going nutz with the spooling.

after the 10mins the car turned into a wrx/boxer engine. as soon as you give it gas in any gear, it goes boxer. when it idles it idles at 1050rpm, too high. the car will rev all the way out in neutral.

There is no black/blue/white smoke coming from my exhaust pipe.

if someone/anyone could give me a run down of things to check, i would much appreciate this. thank you.

Link to comment
https://www.sau.com.au/forums/topic/230839-my-rb26-turned-into-a-boxer/
Share on other sites

have u pulled the plugs & checked if any have started to foul?

the rev limit hasnt been set extremely low has it?

the reason for it revving in neutral i would say would be the fact that its not under any load.

Edited by YLD-CHLD
so when you say it goes into boxer mode, is the thing running rough or???

I would try a compression test next to eliminate that being the problem.

boxer mode.. it runs very rough. no power. but it will rev without limitation just very roughly.

comp test, will do when i get my hands on one of those things.

have u pulled the plugs & checked if any have started to foul?

the rev limit hasnt been set extremely low has it?

the reason for it revving in neutral i would say would be the fact that its not under any load.

ill check the plugs now. the rev limiter has never been touched, stock gtr.

i have had the injectors cleaned only 2 weeks ago.

ok i played with it again. i didnt pull the plugs out to check which one was fouling... do that tomorrow.

but when i was playing with the AFM plug the car started dying and doing what it does when im on the road in gear, wrx'ing.

The plug on the back AFM is damaged, as in where it used to have the plastic extension to bundle the wires with, that has disappeared because it has been hitting the power steering pump reservoir. Each time you touch this plug the car goes funny and idles like a 5 cyl car.

BTW it is NOT the AFM, I have eliminated this with a working set of AFM from another R32 gtr.

=)

Each time you touch this plug the car goes funny and idles like a 5 cyl car.

BTW it is NOT the AFM, I have eliminated this with a working set of AFM from another R32 gtr.

=)

Doesnt that tell you something?...........Youve found the problem yourself. The wiring to the AFM is dodgy and should be re-done. Of course the other AFMs will show no difference since youre only changing the meter and not the wiring. I had the same problem and bought a brand new plug from one of the sponsors on here and it fixed the problem.

Doesnt that tell you something?...........Youve found the problem yourself. The wiring to the AFM is dodgy and should be re-done. Of course the other AFMs will show no difference since youre only changing the meter and not the wiring. I had the same problem and bought a brand new plug from one of the sponsors on here and it fixed the problem.

you get a star next to your name! lol. nah thanks for your imput.. i sort of gathered that that could contribute to the problem, but didnt think it would be so easy to figure out. let hope that when i fix this problems will go away.

so do you remember where you bought the plug? =)

ok. im adding more to this saga.

the AFM seems to be okay after all this. check the plug wiring, checked the afm solder joints, so that part is good.

Now when I start the car it is permanently in WRX mode.

I re-checked the ignition loom and tested each cylinder for a rev drop. Number 4 seems to be the only one that doesnt respond to a rev drop. I pulled out the spark plugs and Number 4 seems to be fouling, full of black crap.

to make sure it wasnt the coil pack, i switched coil pack number 4 with coil pack number 2 and the problem still is at cylinder 4.

I checked all the wiring i could and I can only think of the ignition module.

BTW: I checked the ECU light and got an all clear from the codes.

what is going on boys and girls?!?!?!

i had the exact same problem when i changed my sparks.... the mechanic who changed them didnt clip the electrical clips properly when putting it all back together and it sounded like a rexy and used allot of fuel, poor power and the car was shaking alittle. I just upened the cover where the coilpacks sit under and checked them all. problem went away after i clipped everything properly.

that was my solution to something with the same sounding problem but yours is something alittle more harder than mine....

i had the exact same problem when i changed my sparks.... the mechanic who changed them didnt clip the electrical clips properly when putting it all back together and it sounded like a rexy and used allot of fuel, poor power and the car was shaking alittle. I just upened the cover where the coilpacks sit under and checked them all. problem went away after i clipped everything properly.

that was my solution to something with the same sounding problem but yours is something alittle more harder than mine....

yeh thanks mate, it could well be the clips but ive been over those many many times. cheers.

keep em coming team!

sounds like its getting fuel but no spark.

I would reckon ignitor module related. Even if it is buggered it wont necessarily throw an ECU code.

PS have you checked compression on no 4?

yeh seems like no spark in number 4. i think it could be ignition module related as well. ah thanks for mentioning that it might not show up on the ECU codes.

I havent checked the compression of number 4. how do i get one of those done, is it pricey? would they check that on a dyno as well?

Buy a compression gauge, they arent expensive. You just crank the engine over with all plugs out and the gauge in each cylinder. One at a time of course. Should read 150-160 PSI if its pretty fresh or slightly lower if its got a few km's on it. You need to do this before anything else to rule out mechanical fault.

Deren

OMFG EVERYONE!!!!!!

THE GTR IS BACK!!!! THE POWER IS AMAZING! OMFG OMFG OMFG

I will write a post on my experience in the 1 year of no power.

THANK YOU TO ALL those patient guys/girls that gave input to the issues, your advices were well worth it and were not looked over.

A little word to tease all of you about the post i will write.... spark.

WOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO

OOOT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...