Jump to content
SAU Community

Recommended Posts

I am re-posting this as a lot has changed from the original add.

I am selling this either complied or uncomplied. Unfortunatley i have run out of money after the engine rebuild and the other work i had done. So i now cant afford to get it complied and shipped to me and license it. So i need to move it asap. The car is running and ready to be complied.

Details are:

99 Series 2 Autech 260RS

Pearl white

100,000kms

Car is on the GOLD COAST

All new engine just been rebuilt at Gavin Wood Autotech on the gold coast with all new parts

forged pistons

forged rods

trust cams

trust head gasket

tomei sump baffel

tomei oil restrictor

Garret 2860-7's

N1 oil pump

new water pump

all new timing gear

head recon'd

new valve guides

engine fully balanced

block preperation

exceedy clutch

new engine mounts

new gearbox mounts

new master cylinder

freshly serviced stock injectors

car also has:

HKS Pods

HKS cat back

HKS coilovers

NISMO clear side indicators

There's probably more i have forgotten.

I have had the engine bay re-sprayed whilst the engine was out and any rust/dents scratches etc also removed/resprayed etc.

Im after $35,000 as it sits now uncomplied or $38,000 complied.

I have reciepts for over $17,000 for the engine work.

in can be contacted on 0419943997

sorry about the crappy pictures there all i have.

post-11869-1218175050_thumb.jpg

post-11869-1218175056_thumb.jpg

post-11869-1218175061_thumb.jpg

post-11869-1218175067_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/231531-autech-260rs-series-2/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...