Jump to content
SAU Community

Whats This Pipe Called?

DS-ZILR

By DS-ZILR,
in Victoria

 Share

Recommended Posts

DS-ZILR Collaborator

DS-ZILR

Posted
Posted

gday crew need to know the propper name of the rubber pipe that comes off the metal pipe on my rb26 that says twin turbo on it. the rubber pipe that is on the front side of car end has split not cool and need a new one. the name of it would be cool so i can look it up on the net. please let me know if you know.

cheers

dion

post-49662-1219899023_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/233702-whats-this-pipe-called/
Share on other sites
toddlls Proficient

toddlls

Posted
Posted

That would be the turbocharger air outlet tube(metal one) and outlet hose- thats all the engine manual says, sorry can't help you more. I know on mine there is a lower and upper hose so it wont be the elbow to intercooler (inlet) hose-lower but elbow from outlet tube-upper you should be safe- page EN-58 & EN-69 in JPNZ R32 Engine Manual

DS-ZILR Collaborator

DS-ZILR

Posted
  • Author
Posted
That would be the turbocharger air outlet tube(metal one) and outlet hose- thats all the engine manual says, sorry can't help you more. I know on mine there is a lower and upper hose so it wont be the elbow to intercooler (inlet) hose-lower but elbow from outlet tube-upper you should be safe- page EN-58 & EN-69 in JPNZ R32 Engine Manual
Its just the hose after the turbo outlet merge.

I dont have one, but PM GO_NUTS (he is in QLD) and selling all sorts of piping at the moment

Thanx crew helps heaps. i lost my gtr manual it was on a cd but i have misplaced it.

thanks again hopefully can get a new one now.

regards

dion

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...