Jump to content
SAU Community

Recommended Posts

hello everyone just need some turbo advice thinking of upgrading to this T3 Hybrid turbo specs 0.63 rear, 0.60 front housing, 61mm front wheel t3 hi flow turbo stage 3 wheel

how much power can i expect to make and also what rpm will this turbo spool up at

turbo is going to be fitted to rb25

thanks

Edited by rbgtst
Link to comment
https://www.sau.com.au/forums/topic/234057-rb25det-t3-hybrid-turbo/
Share on other sites

is it one of the old turbos made by HYBRID or is it just an ebay "hybrid" t04? i used a HYBRID branded turbo on a R34 GTT awhile back and it worked ok (bit laggy but not too bad) made 280ish.

hello everyone just need some turbo advice thinking of upgrading to this T3 Hybrid turbo specs 0.63 rear, 0.60 front housing, 61mm front wheel t3 hi flow turbo stage 3 wheel

how much power can i expect to make and also what rpm will this turbo spool up at

turbo is going to be fitted to rb25

thanks

The easiest way to do this is to figure out how much power you want first, if you want 300+rwkw then that turbo wont be much good due to the .6 rear and the fact its probably bush bearing, if your aiming for 200-250 then it will probably will do the job, but so would a high flow which would cost you less in the long run due to the fact that it is a bolt on, no need for custom dumps or inlet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you mean the alarm immobiliser; theyre internal to the alarm itself which makes that difficult; I couldnt even see where he put it; its not in the same place as last time; but with all black wiring it might be very challenging to trace  I had someone turn the key for me as I know it only primes for a couple of seconds As my post above; I am getting no voltage to the pump at all; but I am testing continuity of the power line (SB) from the pump plug to the relay fine. As well as the negative from the pump plug to a 12V constant.    Yeah; he blammed the no start on a bad battery; said I needed to get a new battery and it'll start. Turns out the battery drained because the tail lights had been on for half the day during the install (the rubber cushion on the brake switch gave out while he was testing it as I have a picture of the car from that morning with the tail lights off..i've replaced that). The battery was turning over the engine just fine for a long time; but got low since lights were draining it so it was too low to test a start after he finished. I bought a new one on his advice...$250 wasted. My original battery charged up just fine and is healthy.    It was running perfectly fine when I messed up the old alarm (programmed out the remotes). He couldnt start it after removing the old alarm; my assumption is that when he unhooked it; he didnt bridge the circuit back when trying to start it. Its always been perfectly fine. The ECU swap and pump were 2 years ago. It's never missed a beat in that time. 
    • This is a big issue for me without the diff. I just have zero drive from the passenger side when drivers side has no traction. Bec's parents place has a crazy steep driveway with odd camber and I have never been able to get up. My bro-in-law's 130i with an (unknown brand) LSD gets up fine as does their dad's Hiace. My car stays at the bottom. We have other odd camber roads around here as we're elevated a bit and if it's raining I can get totally stuck around some hairpins. 
    • Yeah, I am super excited for this.
    • Was the car running before he touched the car?
×
×
  • Create New...