Jump to content
SAU Community

Recommended Posts

hey guys up for sale is my cefiro,

1988 nissan cefiro

rb25det series 2 motor + gearbox.. old owner said had only 30k on it

engine work:

low km's rb25 series 2 motor using castrol edge racing oil.

apexi powerfc computer tuned to 220rwkw@1-bar

garret 2876r .64 housed ... 1yr old

sard 550cc injector's...brand new

gredy profec B spec 2

splitfire coilpacks

gredy "copy plenum" with custom pipe work

3inch exhaust + highflow cat

600x300x76 fmic

nismo engine mounts

engine oil cooler + remote filter

powersteering oil cooler...

huge aluminium radiator + remote hotspot/header tank...

gate's racing radiator hose's top n bottom hoses

arc plumbback bov

catco 3-way cat ..near new

battery relocated to boot

driveline:

series 2 rb25 gearbox redline shock proof oil used." stronger of the series"

exedy brass button clutch

welded 4.3 ratio diff using castrol lsx90...

custom tailshaft to fit series 2 rb25det gearbox

nismo gearbox mount.

suspension + brake's

g4 coilover's

custom roadholder adjustable sway bars...

pillow ball adjustable castor rods....

bendix ultimate pads.. stop fine no issue's.

interior:

justjap "recaro style" seats

5 point harness

autotechnica steering wheel

razo gearknob

1x boost gauge

bolt in full cage with front section remooved

rear seats are remooved + seat belts"engineerd as a 2 seater"

exterior,wheels etc:

work meister's black,polished lip 17x8front 17x9 rear +30 offset roughly

federal 595's front n rear

rays wheel nuts

std body kit

the car is fully engineerd for all mod's and is also mod plated.

the bad:

the car has just had registration cancelled due to the defect.

the paint work needs a polish, not been cut back since resprayed

the doorjam's are the old colour and there's a crack in paint work on the bootlid

im a mechanic by trade and i look after my car's. always serviced every 2-3000km

all fluid's have been changed, timming belt,idler's tensioner's water pump etc done.. near new tyre's etc.

pm for contact, can arrange for inspection. feel free to ask any questions u like.no joyride's unless i feel the person is genuinly intrested... no test pilot's either" i will be driving on any test drive's given"

alot of time and money went into this daily/weekend warrior.

accepting offer's around $13000...

im open to offer's for swaps must be rwd and turbo.

image009ry9.jpg

Edited by dead32
Link to comment
https://www.sau.com.au/forums/topic/234562-rb25ed-88-nissan-cefiro/
Share on other sites

I can vouch for this car in the previous owners hands.

He looked after it like a true enthusiast - and used it to kick my GTR's ass one time.

Good luck selling it, it should be sold pretty quickly

I can vouch for this car in the previous owners hands.

He looked after it like a true enthusiast - and used it to kick my GTR's ass one time.

Good luck selling it, it should be sold pretty quickly

thanks for the kind word's steve-o... its only been improved upon since ando had it :(

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...