Jump to content
SAU Community

Have Parts To Se But Unsure Of Value.... Please Help

onevia_dreamer
 Share

Recommended Posts

onevia_dreamer Explorer

onevia_dreamer

Posted
Posted (edited)

hey guys pulling a couple of parts off a dr30 and need to know what there worth as i have no clue but dont wanna be ripped off.

anyway i have complete dr30 interior minus passenger seat and dash as im keeping them. but everything else is there including door trims, rear seats, carpet, drivers seat, side plastic trims ect ect. its red and black in colour and in good condition.....

also a turbo back 3inch exhaust system for an fj20et dr30.....

front dr30 strut and brake assemblies, boths sides.....

let us know as they will all be up for sale in a week.

Edited by onevia_dreamer
Factory 5 Mentor

Factory 5

Posted
Posted

DO YOU HAVE THE IRON MASK FRONT END?

im on the hunt for DR30 front struts & brake assemblies, iron mask filler panel,

the exhaust sounds like a good one too

the best thing you can do is take picks of it all, and make it open to offers

some guys reckon the parts are like gold, and cant seem to sell the bits until the finally realise its just metal and sell it at the current market value, not the perceived value thought up by the the owner

but pics up matey...

onevia_dreamer Explorer

onevia_dreamer

Posted
  • Author
Posted

i will put pics up as soon as i strip the car next tuesday. i dont have the iron mask front end sorry. but as for the front fj20 brake and strut assemblies i thought they would be worth close to the $250 mark. well thats what ill be asking for them. also just noticed the front struts have electronic damper adjustment built in.

i would have thought the interior would be worth around the $300 mark without the passenger seat or dash.

and the exhaust probly around the $400 mark as i just had a full system rigged up for my s13 and set me back 1k!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...