Jump to content
SAU Community

Recommended Posts

Hey all, so iv read the R32 ac thread here, i have a very similar issue

when i turn the temp up to anything over 18-19degrees, it just blows HOT air. Its like i cant get semi warm/cool air, its either HOT or COLD air.

Any ideas? cars an R33 25t. The AC works sweet, its just that it blows COLD OR HOT, NOT semi cool/warm..

THanks :)

Link to comment
https://www.sau.com.au/forums/topic/236814-r33-ac/
Share on other sites

this should only happen when the air temp sensor behind the dash is unplugged or broken.

mines removed atm, so it does the same thing, hot until you put it to 18 deg.

do a search to check for error codes on the aircon, im sure there is a walkthrough that could confirm this for you.

Link to comment
https://www.sau.com.au/forums/topic/236814-r33-ac/#findComment-4156064
Share on other sites

Alright i just ran the diagnostic. For the ones above who dont know how to, heres the link. Soo easy.

http://www.skylinesaustralia.com/forums/Ai...ic-t204597.html

The error codes i got were

22, 25

30

41

5

Any ideas ?

Link to comment
https://www.sau.com.au/forums/topic/236814-r33-ac/#findComment-4158814
Share on other sites

Where your windscreen wiper stalk is next to your steering wheel, right behind it on the dash you will notice a little vent thing. Pull your dash apart and its behind that. Will have a plug going into it, could be unplugged.

Link to comment
https://www.sau.com.au/forums/topic/236814-r33-ac/#findComment-4160165
Share on other sites

All fixed!!!! took out the front of the dash console and had a look at the sensor, 1 of the pins was bent and wasnt in. straightened it and plugged it properly.. oh and i cleaned it out too.. washed it out.. now it works sweet!!

cheers guys :closedeyes:

Link to comment
https://www.sau.com.au/forums/topic/236814-r33-ac/#findComment-4161101
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That looks good, but I think you're going to need much beefier side skirts now.
    • They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • Define "starting to fail". Wy not just rebuild them?
    • Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...