Jump to content
SAU Community

Recommended Posts

hey guys,

i got this funny noise coming from somewhere near the fan belt. its like a woo woo wooo sound, it so loud it annoying. its come on when the engine is about warm, i would go and tighten it and it would stop then it'll start agian after a few minute drive. i've search and some say it the timing belt so i took of the cover and it look nice and tight not to tight tho. it has the gate sticker on the timing cover saying when it was change. but the timing belt is black i thuoght they were blue? the gates one?

another problem is when ever i turn on the aircon i hear a click noise and just under the fan belt that thing that sping for the air con, it spin and stop then go back to spinning is it suppose to do that? i think it only start to happen when i started to tighten the fan belt. also my power steering feel abit harvey once it warm up also?

sorry my english suck bad!!

thank guys

Link to comment
https://www.sau.com.au/forums/topic/239907-fan-belt-and-air-con/
Share on other sites

The woo noise isnt just the clutch fan is it? It will lock up once you get it hot enough and start to make a noise with engine RPM.

Dont worry about the clutch on the a/c compressor kicking in and cutting out. Its cycling, its supposed to do that.

Check your power steering fluid level in the reseviour.

  • 2 weeks later...

hey guys the noise is still there. if my rev is above 750 the noise wont be there but at night when i turn on the lights the revs drop and the woo woo noise would come back on.

any ideas? the fan seem pretty lose, it spin pretty fast too.

Edited by s1.533

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...