Jump to content
SAU Community

Fs: Ssr Professors S1

nerm

By nerm,
in Australian Capital Territory

 Share

Recommended Posts

nerm Mentor

nerm

Posted
Posted (edited)

hi y'all,

i have four wheels for sale

2x Chrome SSR Professer S1 17x8 +38 (unsure for offset and will confirm tonight) with brand new tyres.. 235/40 (or 45?)

2x Chrome SSR Professer S1 17x8.5 +28 (unsure for offset and will confirm tonight) also with brand new tyres.. 235/40 (or45?)

these wheels came on the car and have gutter rash and other scratches etc.

also have two 4mm spacers that were on the front of my car when it was purchased which the buyer can have

come over for a look or a test fit (i have a jack)

looking for $900 willing to negotiate (tyres alone were $640)

PS - im pretty sure that the fronts (17x8) will not fit on a R32 gts-t m-spec (4pot front calipers) without a spacer (unless you grind down the caliper cover). ZCR test fitted the rears and it looked... awesome!! fills the guards nicely

PPS - the picture below is the wheels on my car with the old tyres still on them

call 0410 149 689

Nerm

Edited by Ex!$t3nZ
Link to comment
https://www.sau.com.au/forums/topic/239949-fs-ssr-professors-s1/
Share on other sites
nerm Mentor

nerm

Posted
  • Author
Posted
2x Chrome SSR Professer S1 17x8 +38 (unsure for offset and will confirm tonight) with brand new tyres.. 235/40 (or 45?)

2x Chrome SSR Professer S1 17x8.5 +28 (unsure for offset and will confirm tonight) also with brand new tyres.. 235/40 (or45?)

for some reason i cant edit my original post but i thought that i should point out that the stud pattern is 5x114.3 although the more astute readers will notice that i mentioned that ZCR had them on his 32 which as you all should know is 5x114.3 as well. Note sure if you guys knew that the JizZseX100 was 5x114.3 or not

nerm Mentor

nerm

Posted
  • Author
Posted
whats the width????

and any pics of them on a 32 or what????

what do you mean by width.. in the original post i said that the fronts were 8 inches wide and the rears were 8.5.. or are you refering to the tyres which are 235/40 (or45) all around

no pics of the 32 unfortunatley..

nerm Mentor

nerm

Posted
  • Author
Posted
i gave the number a call but the guy said it was the wrong number haha

oops my number us 0410 146 684.. my bad. i was at the physio anyway so i wouldnt have answered

im not sure if the wheels fit the front with the spacers.. i havent checked

nerm Mentor

nerm

Posted
  • Author
Posted
tried calling that one and it says youve got incoming call restrictions activated haha.

wtf.. sim card must have slipped or something?? this phone has been giving me nothing but grief lately, i might need to get a new one..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • GTSBoy
      Another "where do these lines and plugs go" RB25DET question

      By GTSBoy · Posted

      4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • GTSBoy
      R34 GTR Seats / No longer reclining

      By GTSBoy · Posted

      Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • GTSBoy
      R34 Skyline climate control unit transistor

      By GTSBoy · Posted

      Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...