Jump to content
SAU Community

Recommended Posts

hi guys i have to buy some new tyres . The size i have on at the moment is 245/35/19 front and 275/35/19 rear. The rears are good at this stage but i need to replace the front two.

What i wanted to know was from everyone's experience whats the best tyre they have found in regards to wear and performance. Im not after something that wears down by the day and incredible handling. I just want to hold a bit of grip in the dry and wet .

Also i have found a set cheap on ebay but the size is 235/45/19 will they fit without rubbing the guards. Does anyone else have this size tyre on . My car is factory height from what i can see .

post-55737-1226371759_thumb.jpg

Edited by manda23
Link to comment
https://www.sau.com.au/forums/topic/244308-tyre-size/
Share on other sites

Check this website to see what size you need.

http://www.miata.net/garage/tirecalc.html

I think those 45 profile will throw your speedo out by too much.

Cliff

Thanks whats the stock tyre size for v35 coupe 2003. ?

What tyres have you found to be good value for money

Link to comment
https://www.sau.com.au/forums/topic/244308-tyre-size/#findComment-4254695
Share on other sites

45 profile is for 18s, 19s you will have to step down to 40 or 35 depending on tyre width to keep the rolling diameter and speedo accurate.

A few good tyres I recommend which I have used:

1. Falken FK452

2. Sumitomo HTR-ZIII

3. Federal SS595

They are decent tyres with a good combination of grip and wear without blowing the budget. If the above is still not within budget then ur next step down are your Nangkangs, Maxxis and Nexens.

I normally use this calculator to work out tyre sizes. Stick in the factory specs eg: 225/45/18 and insert the possible tyre profiles in 19s which you are after. Rule of thumb is you should stay within 15mm of stock diameter.

Link to comment
https://www.sau.com.au/forums/topic/244308-tyre-size/#findComment-4254775
Share on other sites

45 profile is for 18s, 19s you will have to step down to 40 or 35 depending on tyre width to keep the rolling diameter and speedo accurate.

A few good tyres I recommend which I have used:

1. Falken FK452

2. Sumitomo HTR-ZIII

3. Federal SS595

They are decent tyres with a good combination of grip and wear without blowing the budget. If the above is still not within budget then ur next step down are your Nangkangs, Maxxis and Nexens.

I normally use this calculator to work out tyre sizes. Stick in the factory specs eg: 225/45/18 and insert the possible tyre profiles in 19s which you are after. Rule of thumb is you should stay within 15mm of stock diameter.

The ones im looking at buying is the pirelli p-zero 235/45/19 i can get them for $600 for the pair. Also the yokahama in 245/35/19 for $600 for the pair. Have you or anyone heard of a italian tyre starts with the letter M ?

How much is the falken's ?

Link to comment
https://www.sau.com.au/forums/topic/244308-tyre-size/#findComment-4254799
Share on other sites

Falkens cost me just over $300 for 265 in 18s. Do not get the pirellis in the 235/45/19 as it is way out and you will probably start scrubbing...Tyre starting with M...Michelin?

i guess i will have to let me pirelli go then. And the tyre is not michelin something else. I saw alot of them listed on ebay before and now they are hard to find. I will try doing a search for them alot of people using them give them the thumbs up.

Link to comment
https://www.sau.com.au/forums/topic/244308-tyre-size/#findComment-4254841
Share on other sites

yeh i think if anything the biggest profile you'll want to go is 40...judging by ur picture though 45's wouldn't look/be too bad...do the 245's stretch? what size is ur rim?...if 245's don't stretch on ur wheel u can get 235 but by the looks of it 245 should be the best choice.

Link to comment
https://www.sau.com.au/forums/topic/244308-tyre-size/#findComment-4254850
Share on other sites

yeh i think if anything the biggest profile you'll want to go is 40...judging by ur picture though 45's wouldn't look/be too bad...do the 245's stretch? what size is ur rim?...if 245's don't stretch on ur wheel u can get 235 but by the looks of it 245 should be the best choice.

I have no idea what you mean by stretch . I dont know the size of the rim either . But a few people have said falken tyres seems to be ok for the money.

So you think the 235/45/19 would fit ok on these wheels

Link to comment
https://www.sau.com.au/forums/topic/244308-tyre-size/#findComment-4254956
Share on other sites

45 profile is for 18s, 19s you will have to step down to 40 or 35 depending on tyre width to keep the rolling diameter and speedo accurate.

A few good tyres I recommend which I have used:

1. Falken FK452

2. Sumitomo HTR-ZIII

3. Federal SS595

They are decent tyres with a good combination of grip and wear without blowing the budget. If the above is still not within budget then ur next step down are your Nangkangs, Maxxis and Nexens.

I normally use this calculator to work out tyre sizes. Stick in the factory specs eg: 225/45/18 and insert the possible tyre profiles in 19s which you are after. Rule of thumb is you should stay within 15mm of stock diameter.

+1 on the sumitomo HTRs. had them on my S15. nice in wet and nicer in the dry!

and thanks for that site Clikar23

Link to comment
https://www.sau.com.au/forums/topic/244308-tyre-size/#findComment-4254980
Share on other sites

+1 on the sumitomo HTRs. had them on my S15. nice in wet and nicer in the dry!

and thanks for that site Clikar23

Im not really concerned that much about money value just handling and wear. I have never been a fan of falken . For some reason always like the brands like pirelli , michelin and yokohama.

Has anyone used the yokohama AVS im looking at getting a pair in 245/35/19 for $600 pretty good deal i think.

Link to comment
https://www.sau.com.au/forums/topic/244308-tyre-size/#findComment-4255006
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...