Jump to content
SAU Community

Factory Immobilizer Question / Problem

rtune

By rtune,
in Car Audio & Electrical

 Share

Recommended Posts

rtune Experienced

rtune

Posted
Posted

If I come back to the car and unlock the doors using the factory fob, I can't

start the car, the dash lights up and the fuel pump runs - but the starter doesn't kick.

the only solution is to get out of the car and lock then unlock the car *with the key

in the drivers door lock* -- then I can start the car.

Is there a reset procedure for the factory key / immobilizer? does the key have

a chip in it?

JLTS13 Enthusiast

JLTS13

Posted
Posted (edited)

there is no reset procedure as such that l know of for the key(if factory NATS nissan anti theft) at most it can be reprogramed with the consult2,as for remotes they can be reprogramed but it shouldnt stop car from starting(unless aftermarket immobilizer fitted), the best bet is to go to your local nissan dealer and get them to check any faults/codes with the consult2 using the NATS card.

Also what model is your car? if it has factory immobilizer(nats) then yes it does have a chip in it.

Edited by JLTS13
rtune Experienced

rtune

Posted
  • Author
Posted
there is no reset procedure as such that l know of for the key(if factory NATS nissan anti theft) at most it can be reprogramed with the consult2,as for remotes they can be reprogramed but it shouldnt stop car from starting(unless aftermarket immobilizer fitted), the best bet is to go to your local nissan dealer and get them to check any faults/codes with the consult2 using the NATS card.

Also what model is your car? if it has factory immobilizer(nats) then yes it does have a chip in it.

I'll try the local nissan place, thanks.

r34 vs2, and yeah I am sure it came stock with the remote locking / immobilizer. It has a red led in the dash.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Duncan's V37.......race car?

      By GTSBoy · Posted

      I don't like "actual computers" for in car use. They take time to boot up, have OS annoyances, and so on. Arduinos etc are ready to go a few seconds after power on, don't mind being agressively powere cycled, because everything is non-volatile, don't mind being shaken and stirred.
    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      As Fred would tell us, it's all about interpreting the rules. It's not a water sprayer, it's a water mister... But everything else you've said, 100%! Even a raspberry Pi would be great, use HDMI out for a display, and add a raspberry Pi CANBus hat to read values out from the ECU.
    • GTSBoy
      Duncan's V37.......race car?

      By GTSBoy · Posted

      Being a race car, and being in the era of the Arduino, one would think it would take little effort to build a controller to do the spraying based on a real physical measurment. Waaaaay back in the dim dark AS days, JE "designed" (as in, he had help) a microcontroller based intercooler spray system. It watched the difference between a temp sensor stuck on the core and one in the free air in front of the cooler, and if the temperature difference exceeded a (settable) threshold, it would activate the sprays. Thus, it only ran water when there was an actual need for water. If you stop to think about the actual physical things that are going on in that stack of coolers, there's probably at least a couple of triggering conditions one could come up with, and one could probably even run one pump with more than one solenoid valve, to allow water to be placed where it is needed, or at all points at once (if it is needed at all points). We're in the age of science baby. But.... I suspect that intercooler water sprays are on the forbidden list in most circuit classes, no? So only good for Targa type stuff?
    • MBS206
      Torana Lx Gtr Hatch, Lots Of Pictures

      By MBS206 · Posted

      I'll just leave this with, holy shit, those cars at work are awesome, and this will look wicked!
    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Could you modify this duct so instead it pushes the extra air through the radiator too and not down and out? For temps, I know it's not the greatest idea, but as a bit of a last resort, you could use a very intermittent misting spray onto the front of the coolers/rad. You don't want to be soaking them such that water is dripping off, but a small most on/off so that the water evaporates. That point of it constantly evaporating, rather than being soaked in water, will pull a LOT of heat out of the cooler. I'm literally thinking just the little mist sprayers for a garden from Bunnings. Being in a low humidity climate it will help even more! The other trick if you want to be ghetto is some shade cloth hung in the opening, and keep it wet. Pretty much now it's acting like an evap cooler on a house, but cooling the air you need to use to cool the radiator...   On a topic to think about too though, when air enters through the bumper, is it all nicely ducted from the edges of that opening back at a nice angle, or is it like most cars, and the edge of the opening just stops, and suddenly it's wayyy wider behind that? If it does the later, get it shrouded out at nice angles. When that opening changes too rapidly, it can actually cause a high pressure zone between the front bar and radiator, and limit air flow into that area, which means less air for cooling, as it effectively stalls the air, AND adds to drag...
×
×
  • Create New...