Jump to content
SAU Community

Recommended Posts

Firstly, it is impossible to get the original finish back. The only way to repair a front lip is to repair it via the method you spoke of (plastic welding) and then to prime and paint it.

I have been through this before. Painting is your only option. It is impossible to match that 'elephant scrotum' finish that is on the front lips from factory.

I have a MIDORI carbon fibre fron lower lip but it was damaged and repaired. It has to be primed and painted, but at the moment it is bogged and you can still see the carbon. I think they are about $1100 so you can have it for $400 if you want.

Oh yeah, also, Joe you are mistaken. Last time i checked with a genuine nissan dealer, a brand new genuine front lower lip for a BNR32 GTR was about $830, not the $490 that you claim.

PM me if interested.

Tom

Link to comment
https://www.sau.com.au/forums/topic/24455-32-gtr-bottom-lip/#findComment-522667
Share on other sites

BNR32, I have had this sort of repair done in Sydney. They can recoat the bar in a plastic finish that is actually heated onto the plastic after it has been plastic welded. The finish is as good as new and will not peel like paint will (and yes they can match the original black/grey colour)and the cost to do it is very reasonable. Nothing is impossible, you just need to know the right people.

The price for the lower lip is accurate as I've just bought one through nissan. The trick is to go to your local smash repairer and get them to order it in for you. They get a discount from nissan and you give them a case of crownies for there efforts. $830 for the lower lip is a bit overboard. I was quoted $560 to buy it over the counter, I think you should check again on that one.

Link to comment
https://www.sau.com.au/forums/topic/24455-32-gtr-bottom-lip/#findComment-523175
Share on other sites

My bar got repaired once and resprayed then damaged it again, this time the damage was a bit more serious then a scratch, so i decided to get different style front bar altogether

maybe something to consider

Link to comment
https://www.sau.com.au/forums/topic/24455-32-gtr-bottom-lip/#findComment-523268
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...