Jump to content
SAU Community

Haltech Interceptor On Rb25det

Ninja_09

By Ninja_09,
in Engines & Forced Induction

 Share

Recommended Posts

Ninja_09 Apprentice

Ninja_09

Posted
Posted

Hi everyone!!!

I've just signed up on the site so I'm not sure what am doing and if I'm in the right section.

I had the R33 S-II for about a year and got an Interceptor fitted. Eve since I had it I have issues with ignitions around 3.5 - 4K RPM.

being through 3 different tuners and spent a fortune but same story.

Just wondering if anyone’s successfully done this before?

the car is converted to Manual and got a high flowed turbo , greddy ele. boost controller

Thanks in advance !!! :P

Link to comment
https://www.sau.com.au/forums/topic/246615-haltech-interceptor-on-rb25det/
Share on other sites
Ninja_09 Apprentice

Ninja_09

Posted
  • Author
Posted
try give my tuner a ring, he's in WA and will point you in the right direction. he is a haltech guru

Aaron

in tune performance (bibra Lake)

(08)94346608

Eric

Thanks Eric... Will try first thing tomorrow !!!

I was thinking if this is useless, then get Nistune done. Has anyone done Nistune on a R33 series 2 before. because ignition/ coil packs are different in series I and series II ???

Any ideas pls????

QWK32 Veteran

QWK32

Posted
Posted

i don't think nistune do a board for the R33, S1 or S2. also having the ignitors in the coils doesn't make a difference to the ecu. you've converted to manual, there are better options for engine management out there.

Ninja_09 Apprentice

Ninja_09

Posted
  • Author
Posted
i don't think nistune do a board for the R33, S1 or S2. also having the ignitors in the coils doesn't make a difference to the ecu. you've converted to manual, there are better options for engine management out there.

Thanks for the reply mate !! I know there are few different options out there but it all comes down to the cost of goods and installation then of course tuning. Nistune works out cheap even if I did it using a RB20 ECU, but the question is does this setup work on R33 S-II. I heard it works fine on series I cars coz the ignition is same in RB20 and RB25 series I.

Other option would be to find a 2nd hand PFC…

QWK32 Veteran

QWK32

Posted
Posted

shouldn't be a problem, just have to check all the pinouts and match them up. all that comes from the ecu is the ignition signal, in 32's an S1 33's it goes to an ignitor pack which then fires the coils, in the S2 the signal goes straight to the coil which has a built in ignitor. the signal is the same from the ecu, just handled differently at the engine side of things.

Ninja_09 Apprentice

Ninja_09

Posted
  • Author
Posted
shouldn't be a problem, just have to check all the pinouts and match them up. all that comes from the ecu is the ignition signal, in 32's an S1 33's it goes to an ignitor pack which then fires the coils, in the S2 the signal goes straight to the coil which has a built in ignitor. the signal is the same from the ecu, just handled differently at the engine side of things.

mmmmm that explains a lot and makes sence. !!!! :ninja:

Had a chat to Andrew from Hyperdrive today and also Sam from Dr Drift who's got a daughter board for R33 ECU ($1100). So I guess I can either use RB20 ecu and Greddy MSS(for VCT) to do Nistune or get Sam to install the daughter board onR33 ecu and make it tuneable. I'm wating to hear back from Andrew coz after all he the tuner. I'm paying for not consulting a / the tuner and buying an Interceptor which cannot be properly tuned on a R33. I spoke to Aaron from In Tune today, he's willing to check the wiring and do few test ot see what's wrong but I think it's best to just remove the Interceptor and get a fully functional and well tuneable ECU rather than a piggyback..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Ethanol Content Sensor - Always at 11%?

      By GTSBoy · Posted

      You say potato, I say potato?
    • GregosM10
      Carb issues - E15S

      By GregosM10 · Posted

      Based off what you’ve said here, I think I’ve figured out a good bit of what I’ve done wrong -  So on the line going from the PCV valve to carbon canister, there’s a T joint that is pretty much right next to that lower port - I hadn’t noticed that the hose in the diagram was curved to attach onto the carb, so I was putting that line for the lower port onto the PCV line / carbon canister line instead. I’m going to have a flick through the manual again tomorrow and should hopefully find a diagram that’ll show me where that T joint should be connected to. Timing also 100% needs to be sorted out as well, should be able to tackle that tomorrow as well. Definitely feel like I should be on the right track now though. 
    • dbm7
      Carb issues - E15S

      By dbm7 · Posted

      The screw is for idle (pilot circuit) mixture adjustment. Else, I'm confused ~ the diagram shows 2 carby ports, and the intake manifold port, but you're suggesting the "2nd port on the back of the carb that isn’t mentioned in the diagrams" ...yet, both carby ports are shown...que?... ...in any event, that port should be connected, but if not (like it is now), it's unlikely to cause a backfire out the carby (it would introduce false air and give you a fast/lean idle) ...sounds more like timing issues/spark plug wire routing responsible for the backfiring.    
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's fair, I can see both points. I get enthusiastic when I see the FS section has a new post and want to see what interesting thing someone is selling. Then I get deflated it's a bump of a 10 year old post. Ha ha
    • MBS206
      Ethanol Content Sensor - Always at 11%?

      By MBS206 · Posted

      Couple of litres of moonshine from his southern cousins would do it...
×
×
  • Create New...