Jump to content
SAU Community

QLD and NSW - Chartered Professional Engineers

Steve

By Steve,
in Engines & Forced Induction

 Share

Recommended Posts

Steve Grand Master

Steve

Posted
Posted

Hi,

Anybody out there had mods engineer certified? or know where it can be done in QLD or NSW? EDIT: or in Vic:)

I was making some enquiries into getting mods engineers certified to comply with ADRs.

It would appear that an engineers report from any 'Chartered Professional Engineer' will be accepted, subject to inspection of course.

If anyone can help it would be greatly appreciated, I have done a couple of searches on the web, but information seems scant.

Thanks for your time

Steve

Steve Grand Master

Steve

Posted
  • Author
Posted

Just had a look at the vic roads site, a bit more helpful. Whilst it has signatories for vehicle mods, it is no longer an 'engineers certificate per say.

the crazy thing is it even lists several signatories for NSW, a whole 2 for SA and lots for vic. Might be worht a look if anyone is thinking of doing this:

http://www.vicroads.vic.gov.au/vrne/vrnint...nDocument&Area=

browny Proficient

browny

Posted
Posted

Sorry, VSI15 is the correct document - disregard my first post people.

This information sheet contains a list of people with experience in automotive design and standards who have indicated that they are available for consultation. They are familiar with vehicle construction requirements in NSW and, for a fee, they will provide advice to owners and vehicle constructors, undertake technical assessments and issue engineering certificates. However, in publishing this list, the Roads and Traffic Authority does not endorse their services nor does it take any responsibility for the quality of their work. Vehicle constructors and owners intending to engage the services of an engineering signatory, should establish the signatory's experience for the proposed scope of work and the fee arrangements before work is commenced. It is also advisable to ascertain whether the signatory carries “Professional Indemnity Insurance”.

An engineering signatory who certifies a motor vehicle as to its construction or modification will:

• personally inspect the vehicle;

• ensure that the scope and any construction or modification complies with the requirements of the Road Transport (Vehicle Registration) Regulation 1998 and the Australian Design Rules;

• Issue an engineering certificate in the form specified under the Engineering Certificate System(ECS) (see sample overleaf).

Note: Only an engineering certificate issued by a signatory who is listed will be acceptable to the Roads and Traffic Authority (RTA) for the purposes of vehicle registration.

Engineering signatories included in the ECS are full members of the engineering organisations recognised by the RTA for this purpose, namely:

• The Institution of Engineers, Australia (IE Aust);

• The Society of Automotive Engineers, Australia (SAE-A) - Automotive Signatory Group.

Other information sheets published by the Authority cover the circumstances under which a vehicle constructor or owner may require the services of an engineering signatory. In brief, owners are required to obtain an engineering certificate from a recognised engineering signatory, when performing any modification to a vehicle, which is safety related and affects the continuing compliance of the vehicle with the Road Transport (Vehicle Registration) Regulation 1998 and the Australian Design Rules.

A list of these signatories is attached to this information sheet.

9krpm Mentor

9krpm

Posted
Posted

Steve, I've got some info from Transport SA from a mate who work there.

Here are their approved chartered professional engineers.....you might probably know it aldready :D

1. Tonkin Consulting

2. Australian Technology pty ltd (Regency is a little bit iffy about this guy though...i think u know that toooo)

3. Rory Thompson Services

4. Forensic Engineering and Associates

5. Engineering analysis & software

Now not all of them are catered for our purposes. PM me ur fax no and I see if I can fax this to you if you want a copy.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • LegendGTR
      EFR7670 exhaust selection RB26

      By LegendGTR · Posted

      I'm looking for some real world experiences/feed back from anyone who has personally ran a EFR7670 with a 1.05 exhaust housing or a .83 I'm leaning towards the .83 because its a street car used mostly for spirited driving in the canyons roads. I"m not looking for big numbers on paper. I want a responsive powerband that will be very linear to 8000 rpm. I dont mind if power remains somewhat flat but dont want power to drop off on top. The turbo I've purchased is a 1.05, although the mounting flange T3 vs T4 and internal vs external waste gates are different on both housings, I not concern about swapping parts or making fabrication mods to get what I want. Based on some of the research I've done with chat gpt, the 1.05 housing seems to be the way to go with slightly more lag and future proofing for more mods but recommends .83 for best response/street car setup. AI doesn't have the same emotions as real people driving a GTR so I think you guys will be able to give me better feed back 😀   
    • PranK
      Stock Airbox and Snorkle for RWC - VIC west

      By PranK · Posted

      Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • PranK
      Duncan's V37.......race car?

      By PranK · Posted

      This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • Duncan
      7 Speed Auto transmission fluid change (Skyline, Q50, Q60, Fuga, Q70, A62 Titan and probably heaps of others including Navara...)

      By Duncan · Posted

      OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
×
×
  • Create New...