Jump to content
SAU Community

Rb25det Manifolds Turbo And Injectors Etc

sneaky1
 Share

Recommended Posts

sneaky1 Mentor

sneaky1

Posted
Posted

hi pplz i have intake and exhaust manifold for a rb25det.

these would be good for 25/30 conversion or stock kit to pass vehical inspection.

pretty much its the whole kit including nuts and bolts.

i took these off a blown motor and shoved them aside just incase i wanted to use them at some stage.

throttle body, injectors, fuel reg, nuts and bolts, heat shields inlet and exhaust etc etc.

there is a turbo that comes with this kit but not really sure how good it is.

have had the turbo running but made a noise so it was taken off to fix but replaced instead and couldnt be bothered testing again. was bought as being a high flow 33 series 2. does not blow smoke and minimal shaft play.

any questions just ask.

dont know what this is all worth so make an offer.

post-39965-1230284688_thumb.jpg

post-39965-1230284725_thumb.jpg

post-39965-1230284762_thumb.jpg

post-39965-1230284802_thumb.jpg

post-39965-1230284834_thumb.jpg

post-39965-1230284862_thumb.jpg

post-39965-1230284898_thumb.jpg

  • 5 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...