Jump to content
SAU Community

Recommended Posts

hey guys

was reading through a hot 4's magazine where it said that we should maintain our coilpacks so they don't fail on us. "Removal and inspection is the best bet, with frequent lubrication of the silicone seals that live between the coil and spark plug being the best way of stopping moisture ingress"

can someone clarify where lubrication is meant to occur? i'm afraid i will put lubrication which will inhibit the spark travelling down to the plug

here's a pic if someone wants to draw on it :banana:

splitfire_coils_3.jpg

Link to comment
https://www.sau.com.au/forums/topic/250235-coilpack-maintenance/
Share on other sites

From what I can understand from that statement, the oil is just to help prevent moisture making its way down to the plug and shorting out the coilpack......no?

I don't think this maintenance is going to stop age taking it's toll on the coilpack itself.

Edited by KeyMaker

I don't think i've ever heard of a coil pack failing due to moisture.

Its usually heat, over time, cracking the coil pack casing or they just wear out.

Just ignore hot4's IMO. It doesn't apply to every make, model.

I don't think i've ever heard of a coil pack failing due to moisture.

Its usually heat, over time, cracking the coil pack casing or they just wear out.

Just ignore hot4's IMO. It doesn't apply to every make, model.

its hard to know what to do when you see things like this;

"Corrosion, formed by the presence of liquid around the plug and coil pack, is one of the greatest electrical resistors known to mankind, providing enough of a blockage to the voltage transfer process to keep the spark plug from firing correctly. Once the whole shooting match has been dried out, there is also the ever-present threat of corrosion in the form of white chalky powerd that once more will inhibit the spark plug firing... Always run your centre cover too, as the myths started about coil packs overheating and shutting down are absolute rubbish."

the article contained a test dummy ca18det engine with aftermarket coil packs which produced all over less power and could not even rev out without misfiring (where the standard ones worked fine). i thought it would be applicable as its another similar aged import nissan engine.

but i really have no idea, i havent run a center cover for 18+ months and was a bit concerned i was ignoring the maintennace of my car?

Suggest ignore after you put your new coil packs in. Unless of course your pouring water in the wells. The cover will help but even without a cover I'd suggest you have a decade or more of peace of mind. It will fail from heat b4 it fails from water seeping in.

Hit em with WD40 if your concerned.

BTW ~ What's Kmart Racing? Sheeeezus! mate!

Edited by Sinista32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...