Jump to content
SAU Community

Recommended Posts

The first picture is as I got the car, nismo R1 ECU, it is rated

at 1.1bar however I think it was spiking to 1.3 then coming back to 1.1.

Pretty much it shows the car making 120kw at 4400 rpm and 180kw at 5000rpm

I wanted an earlier spool and to be able to control boost.

So..

An HKS EVC6 was installed (today). and cam gears, new dyno runs. We setup

two boost profiles, basically 16psi high and and 14psi low, (conservative).

Ok now you can see the car hits

* 0.68bar (10psi) by 4400 rpm (at which point it makes 120kw)

* 1bar (14.5psi) by 5000 rpm (at which point it makes 180kw)

and full boost is obtained at 5200 rpm.

then (for both high and low) there is a _steady_ boost taper, losing 3psi

from the high setting and 2psi from the lower setting.

The other snap is from the HKS EVC6 manual which explains two likely problem

boost profiles. The first is a spike, and the second is a taper, but only at the end.

So what is the problem? I'm annoyed about two apparently contradictory

things: late spool and continuous taper.

Shouldn't it be hitting 1bar at the latest by 4000rpm? isn't that the whole point of n1/gtss type twins?

Will a powerfc tune change anything?

---------

specs: N1 engine, R1 turbos (same spec as r34 N1s). nismo AFMs,

intake, weldina exhaust.

The AFR is good: starts at ~13 then drifts down to just below 11s.

by the way, on an initial hks evc6 setting of 11psi boost showed flat. 11psi all the way.

post-51561-1231134416_thumb.png

post-51561-1231134431_thumb.png

post-51561-1231134438_thumb.png

Link to comment
https://www.sau.com.au/forums/topic/251172-boost-taper-late-boost/
Share on other sites

This is the torque and power graph (crank hp) that the setup SHOULD show.

Unless I'm reading it wrong, torque is right up there at 4000 rpm, therefore the turbos

hit full boost by then.

I can see the same power shape from 5600 onwards on the croydon dyno plot, I'm just

totally missing that fat midrange?

post-51561-1231199649_thumb.png

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...