Jump to content
SAU Community

Recommended Posts

Engine:

N1 24U block (own modifications done) race prepped

Fully balanced and blue printed

Chemically cleaned/crack tested and washed

Torque plate bored honed & decked

All new welsh plugs

Tapped oil gallaries

Fully balanced/detailed crank and grub screwed

New Ross harmonic ballancer

Race prepped crank gurdle

Shot peened/prepped standard rods with ARP bolts

Full ARP bottem end stud kit

Ross Racing forged pistons (ceramic coated)

ACL race bearings mains & rods

N1 oil pump (modified)

N1 water pump

Genuine Nissan gasket kit

Fully port & polished head

Match ported intake

Brass valve guids

Standard valves

Upgrade valve springs

Standard cams

Greddy adjustable cam gears

Greddy clear timing cover

Polished intake manifold and valve covers

Gates timing belt

New genuine exhaust studs & nuts

Garrett GT3082r .82 turbo polished front cover

Braided oil lines

Tial 44mm wastage

Ebay spec manifold modified

Greddy twin entry air intake pipe

2 x RB25 Air flow meters

4" dump pipe

4" catback exhaust

600x300x115mm Greddy style intercooler

Custom PBR clutch

Nismo lightened flywheel

Nistune ECU

Sard fuel pressure regulator

custom fuel rail

r33 gtr lift pump

044 fuel pump

2L surg tank

3/8" Aluminium fuel lines

Heap of speed flow fittings & push lock hose

Sard 700cc injectors

Alloy dual core radiator

Silicone radiator hoses

Silicone heater hoses

Exterior:

Full colour change $6000.00

18x9 18x10 roh drift r's

carbon exhaust shroud

carbon tope secret bonnet painted

genuine gtr front bar and gtr grill

rear drift lip

nismo b pillars

tein coil overs

Inerior:

gtr dash cluster

autometre boost guage

hybrid boost controller

greddy turbo timer

smoothed engine bay and seam welded. Hopefully looking for 450rwhp on 20psi. Car is nearly finished

contact:0438774173

Location: Hervey bay qld

$27,500 ono or will swap for 02,03 wrx, toyota chaser, s15 etc

post-11029-1232496153_thumb.jpg

post-11029-1232496167_thumb.jpg

post-11029-1232496181_thumb.jpg

post-11029-1232496195_thumb.jpg

post-11029-1232496207_thumb.jpg

post-11029-1232496224_thumb.jpg

post-11029-1232496236_thumb.jpg

post-11029-1232496247_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/253494-built-rb26-r33-gtst/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

how much would u want for the complete engine if u did sell it, id help find an rb25 if u needed something to replace with.

Very interested in engine. Pm me if you want to cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes the gear for the R33/34 is different, it is red and has a different number of teeth. My part didn't come with that gear though, so I don't know how many teeth are on the red one. You'd have to reuse the 260RS/R33 gear, as long as it's not destroyed.   Haha, as unfortunate as that might be it was working fine for about the first 1500km I've had the car for now.
    • Update all   thanks to the workshop manual, it lead me back to checking fuses as mentioned central locking and door open lights worked when acc was switched on. diagram attached shows two points of power 1. ACC and 2.  Batt with the later being fused (#28) I did check the fuses using a multimeter but I must have stuffed that up also. Went back and checked the batt fuse in interior fuse box and you wouldn’t believe it… a blown fuse. replaced fuse and everything is now working as it should including the climate control   thank you all with your positive insight and knowledge.    
    • Where is the warning "That this thread is super old"   I just went into a 5 year old thread, went to do a reply, and couldn't see anywhere obvious a warning of it being super old
    • Duncan is correct. Pitwork (and Toyota's own cheap brand "Drive Joy") were primarily created as brands to sell other manufacturers car parts. It would be weird if Nissan sold parts for Toyota vehicles with a Nissan logo on it, so they created Pitwork to sell parts for other brans Toyota, Honda etc. They are not the same as Nissan genuine parts, although they *do* meet Nissan's standards for replacement parts. They aren't supposed to be a substitute for genuine parts, but a cheaper alternative that is better than Ebay fake parts from you-know-where.
    • Thanks GTSBoy, much easier to work with it now it's free!  
×
×
  • Create New...