Jump to content
SAU Community

Recommended Posts

Item: Wolf 3D V4(V400) Plug and Play with Hand Controller

Condition: Good... Few scratches on ecu case(not that you ever see it).

Price: $950

To Fit: R33 GTS-T

Location: Central West NSW

I am selling my Wolf 3DV4(V400) Revision 7, Plug and Play ECU with Hand Controller to suit R33 GTS-T. Possibly fit R32 and GTRs(not 100% sure, check with Wolf). The current map on the ecu is for an RB25DET with upgraded turbo, injectors, fuel pump etc.

Some details on the Wolf unit(collected from other posts):

The Wolf 3D Version 4 is fully 3D tunable for both fuel and ignition timing! These ECU's are an excellent unit with incredible tuning resolution, both ignition and fuel can be adjusted every 125rpm with 16 different load bands. Thsi compares very well compared to Microtech that can only be changed every 500rpm with less load points. Having such a fine tuning resolution is perfect for getting the most out of your modified engine. No need for a Z32 AFM with this ECU, simply remove your AFM all together. Overall this ECU provides sharp, crisp throttle response whilst still maintaining factory drivability e.g smooth idle, fuel economy, cold start etc, something impossible with many of the competitors ECUs.

Some of the benefits of fitting a Wolf 3D V4:

Make the most out of your modifications

Excellent drivability, Wolf 3D V4 features full cold start and air temperature adjustments

Easily retuned if you change a modification

Crisp and smooth idle

Excellent fuel economy

Ability to remove AFM. ECU is MAP sensor based so no need for a Z32 or the airflow restriction a AFM causes

Boost controller can operate with factory solenoid

In Built Turbo Timer

Security Pin Code(Car won't start till code has been entered - backup for your alarm/immobiliser)

Can run multiple Maps with live map switching while the engine is running(Power Map, Economy Map, or Low Octane fuel)

Excellent fuel economy

Specs:

Tune from either Hand Controller or PC Software

Maximum Engine Speed 20,000RPM

Fuel Map every 125RPM to 16,000RPM

Fuel Map has 16 Load Bands

Ignition Map every 125RPM to 16,000RPM

Ignition Map has 16 Load Bands

Idle Speed Control with Water Temperature Compensation

Sequential Fuel Injection

I have attached a number of pics(including the unit powered up). Unit was $1790 new (ECU $1395 +HC $395). Looking for $950. Will post. Contact me via PM.

post-4967-1233398528_thumb.jpg

post-4967-1233398566_thumb.jpg

post-4967-1233398630_thumb.jpg

post-4967-1233398711_thumb.jpg

Edited by crazy1
Link to comment
https://www.sau.com.au/forums/topic/255006-wolf-3dv4v400-with-hand-controller/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Guys since i bought r33 gts25t coupe 1994 automatic a/t(manual swap 350z gearbox)  all i got is problems, always problems. Lets start with that when i turn key into ignition(ON) fuel pump doesnt always works. Sometimes i have to turn key twice Off/on/off/on until it primes. Its new, dw300 - 340lph. My gearbox broke so i did gearbox swap, install different intake manifold, injectors and i take pipes. Car was sitting in garage for more than half a year. I did assembly all not that long ago and when i turn ignition cant hear prime. All of sudden it stopped working. Theres many videos on YouTube how to make relay mod on r33 straight from battery so i did and it doesnt work! 😰 30 - battery positive  87 - positive from fuel pump to relay 85, 86 - one of two wires from original fuel pump wires(light blue, grey) and it didn’t work. so I check on ignition and took original BLUE relays wires from trunk, next to fuses. (I believe it’s IGN+ and ECU pin 18. it didn’t work…  tried connecting (IGN+ from og relay) and (ECU 104 from 1of4 FPCM wires) to my new relay 85/86 and it didn’t work.  I unplug FPCM. Didn’t work. im thinking what’s wrong   fuel pump is working, if I leave IGN+ on 85 and 86 straight to ground it works but it’s just nonstop. Since it getting constant 12v after key in ON. light blue wire gives me 6-8v.  so how this should be connected? What causing ECU not giving — on pin? Or I did sth wrong and that’s why it doesn’t work? I need negative signal on ECU that control fuel pump. What this should be?
    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
×
×
  • Create New...