Jump to content
SAU Community

Recommended Posts

Make/Model:

Mitsubish Sigma Scorpian GL

Year:

1983

Kilometers:

185,000

Car Specification and Mods:

2.6L 4 Cylinder Engine (JAP IMPORT) not the Australian made engines which are crap (due to a use of different metals and engineering differences)

5 Speed Manual

Holley Carburetter (180 dual throat, mechanical secondary)

Exhaust (2 inch after factory manifold)

Larger Sigma front anti roll bar

Manual gearbox out of GE Sigma 1850cc

Lightened standard flywheel

Modified tailshaft (to suit gearbox)

Welded center in differential

Firmer (and cut) springs

The tops of the struts have been turned 180 degrees to give slight negative camber

Harder four wheel drive compound front brake pads (Bendix)

Bonnet is shaved and held down by four metal pin-like supports on top of the bonnet

Has a turn-key battery disconnecter complies with CAMs rules.

No airconditioning (can't believe I was even asked this Wink)

Engine was rebuilt and actually has 85000km's on it.

Asking Price:

$1750 cash, make an offer.

Location:

Brisbane

Contact Details:

If you are interested pm and I will get back to you asap.

Other Comments:

This car is really fun to drive, love kicking the rear end out the side its fantastic. Engine is in top notch condition, the car has been so well looked afterl when I bought it, haven't used it so its still in good condition engine is kicked over and run every 2 weeks.

Comes with spare top-end or bottom end of engine some wheels with semi-slicks on them.

I do have another seat for the front left with rails however the rails need a slight modification to be mounted which won't be hard or cost much you just need a welder and 5-8mm thick steel plate and drill some holes weld up to the existing rails and wella you have a properly mounted front-left seat.

Do not have the rear interior.

Also comes with fire extinguisher.

Pictures (Click the pictures for larger view)

th_CIMG4195.jpg

th_CIMG4196.jpg

th_CIMG4197.jpg

th_CIMG4201.jpg

th_CIMG4203.jpg

th_dpig1.jpg

th_dpig2.jpg

th_dpig3.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...