Jump to content
SAU Community

Wanted R31

Evad79

By Evad79,
in Tasmania

 Share

Recommended Posts

SKiT_R31 Experienced

SKiT_R31

Posted
Posted
after a turbo? non turbo? mate of mine has one he might be selling, non turbo 31.

more info? Sedan, Wagon? Turbo i assume? Stock or modded?

White 1986 R31 Wagon, Low King springs, 4wd shocks (stiff), nolathane bushes, R31 Ti wheels, re-shimmed lsd, RB25DET excedy HD organic clutch, RB30e + T, custom turbo - KKR480 exhaust housing and rear wheel (.69AR) and Garret T04B centre bearing and front compressor Housing, running 12PSI, singlesided FMIC, R34 BOV plummed back, R33 RB25 Crossover pipe, AFM in boost (for more resolution), progressive cooler piping - armidillo bends, VLT injectors high flowed/higher fuel pressure for 280cc operation, 280cc remapped ECU, Malpassi Adjustible fuel pressure regulator, Bosch 044 external fuel pump (noisy), fuel surge tank, cold heat range plugs, Bosch GT40 coilpack, NGK silicone ign leads, 180thou km on engine -has perfect 180psi on every cylinder (compression test), 200thou on chassis. Setup was made hoping for 200rwkw, and uilt to look sleeperish, hasnt seen dyno yet.

The gearbox is original S1 30e, doesnt enjoy the power, runs fine in gear or with casual shifts, 2nd gear synchro is worn (cant quickshift second at high revs without a crunch) and reverse has a chipped tooth, so it make a clicking noise - runs fine, oil has been replaced and is clean not silver.

sort of thing you are after?

Link to comment
https://www.sau.com.au/forums/topic/255874-wanted-r31/#findComment-4413005
Share on other sites
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...