Jump to content
SAU Community

Recommended Posts

S14 manual conversion kit: G/C sr20 5 speed manual gearbox included, s14 abs tailshaft, s14 clutch and brake pedals, s14 master/slave cylinders and lines, s14 speedo drive, s14 X-member and mount, used flywheel and clutch, throw out and fork, ebay short shifter, all bellhousing, starter, flywheel, clutch and slave bolts ###Will seperate box, perfer pick up###

$900

post-58828-1234426389_thumb.jpg

SR20 Used manual gearbox x2: Not Neg

1x s13 sr20 5 speed manual, N/R, 2nd gear synchro crunches on downshift, new bearings fitted 18 mths ago(cost $350) $350

1x s13 sr20 5 speed manual, Good condition, selects gears, no rattles $500

post-58828-1234426813_thumb.jpg

SR20 short shifter: ebay base plate version $50

post-58828-1234425195_thumb.jpg

R32 16' alloys x2: 16x6.5', polished silver $50

post-58828-1234423612_thumb.jpg

S14a rear bumper: pearl white, aus spec off s2 $150

post-58828-1234424702_thumb.jpgpost-58828-1234424843_thumb.jpg

post-58828-1234424927_thumb.jpg

S14 - S15 - R33 rear coilovers: HKS/kawasaki, 30 way adjust damper, pillowball top, height seized $250

post-58828-1234426018_thumb.jpg

S14 - S15 - R33 JIC rear toe arms: Joints replaced, Good condition $100

post-58828-1234425589_thumb.jpg

S14 - S15 - R33 JJR Camber arms: Rear upper, Good condition $100

S14 - S15 - R33 KTS Front tension rods: castor bar, Good condition $150

S13 J's headlights: dual square, glass removed, reflectors and platic's covers req repair $250

S14 - R33 Std 16' alloys X4: 16x6.5, 205/55x2 225/50x2 RWC michelin $150

S13 R180 3x2 diff: includes manual n/a tailshaft and 2x halfshafts $150

Random other bits incl: !!!No stereo or console surrounds, lca's, brakes or hubs!!!

S14 dash plastics: vents from $5

S14 single airbag dash $40

S14 radiator and shroud manual $150

S14 s1 rad support $150

S14 Front X-member $80

S14 abs bmc and booster $80

S14 abs pumps s1 or s2 $30

S14a leather steering wheel incl airbag $100

S13 boot trim complete $40

S13 radiator + shroud manual $100

S13 and S14 sr20 engine parts From $5

Located Gold Coast

Prefer pick up

Sam txt 0423 648 114

Edited by RED513
Link to comment
https://www.sau.com.au/forums/topic/256779-sparrows-clean-out/
Share on other sites

Any pics of the S14a Leather Steering wheel please? Is this the Luxury ed?

S14a 1997 series 2 luxury leather wheel inc airbag. Slight tears where thumbs sit (joint in leather) otherwise g/c.

Edited by RED513
  • 2 weeks later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...