Jump to content
SAU Community

Recommended Posts

Aint driven my car on teh Dirt, :P Where can we all park that wont be taken, Pref not on dirt but aint fussed.?

I would normally suggest near cat corner opposite those race sheds, but i think they have RC Drift there on battle days. + they guy at the gate wont let u in.

I normally Grab 1 of 50 Cripple Bays, that are just before the gate/dirt as just about all of these fill up by the time the battle begins, they dont really care unless its like V8 supercars.

Top effort today Sam

But my big thank you goes out to 2 dickheads driving white 33's around the back of CAT CNR

Thanks to those two RETARDS i now have to respray the front bar of my falcon as they had to be heroes and do their gravel burnouts as they were leaving and it sprayed all over the front of my daily

Edited by gazza750

Had a wicked day,

I had a few probs this in the mournin, I wasnt paying any attention and put to much oil in my engine :)

then i went out for a couple practice runs before my qualifiers but bouncing off the limiter for minutes at a time filled up my oil catch can in turn coating my engine bay and windscreen in oil :D

i nearly was disqualified due to the oil spill, i then put a gatorade bottle over the catch can over flow :D

only just got out in time to do 2 qualifiing runs and managed 5th place,

i then versed Dim in the Silvia and won but then lost to Lance Biffen,

I have some in car vids il put up later

bummer about the paint mate. I wonder if they will pay to fix now.

but the drift day was good for me. great to see heaps of R32' out there.

spotted ANGR33 and voted for him too

vid footage

http://s385.photobucket.com/albums/oo299/m...032009090-1.flv

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • New CAS just turned up from NZ Wiring. Looks like a nice bit of gear.  So, yeah. Triggered, bro. Realised I may as well do the cam belt while mucking about with it so will order one of them.
    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
×
×
  • Create New...