Jump to content
SAU Community

Recommended Posts

this is a in my 700hp R32 GTR , box is designed for race track and not that suited for road use. im selling as im not ready for track just yet.

sale will be conditional on swap for buyers working GC GTR box plus $10,000.

box will be out of car in the next few days and serviced, will take photos and post them then

thanks

this is a in my 700hp R32 GTR , box is designed for race track and not that suited for road use. im selling as im not ready for track just yet.

sale will be conditional on swap for buyers working GC GTR box plus $10,000.

box will be out of car in the next few days and serviced, will take photos and post them then

thanks

also has a HKS triple plate clutch with it,

Hey mate

How old is the box,how many kms has it done?

And where are you located?

Thanx Paul

Not sure how old box is , came in car i bought. not too sure how many klms on it either .

(although car has 60,000 kms on it)

Box is in brisbane.

Im putting it in for a service next week , so will take photos of all gears and internals while its apart

How much are these new?

i could be interested as im in the market for a tough box..my trust 6speed dogbox wasn't up to it...

How much are these new?

i could be interested as im in the market for a tough box..my trust 6speed dogbox wasn't up to it...

The "sequential " 6 speed is $22,000

It takes a bit to learn how to use one properly , but when the engine its at full tilt slamming the shifter back up the gears and forward down the gears

it is awesome, the box screams like most serious race cars. very tough street addition to your GTR or good for 9 second passes.

this box came out of a very tuff street car , never been raced .

The "sequential " 6 speed is $22,000

It takes a bit to learn how to use one properly , but when the engine its at full tilt slamming the shifter back up the gears and forward down the gears

it is awesome, the box screams like most serious race cars. very tough street addition to your GTR or good for 9 second passes.

this box came out of a very tuff street car , never been raced .

H patteren box's are 6k 0r 7k sequential are push forward to go down gears and pull back to go up, faster change more direct drive.

this is a in my 700hp R32 GTR , box is designed for race track and not that suited for road use. im selling as im not ready for track just yet.

sale will be conditional on swap for buyers working GC GTR box plus $10,000.

box will be out of car in the next few days and serviced, will take photos and post them then

thanks

Hi I am building a GTR33 track car with a OS giken 5sp. Have not tried a 6sp Sequential yet. My mate who used one advise me that

they are high maintainance item. Interested to have a go.

Alex 0433559972 or PM me

Hi I am building a GTR33 track car with a OS giken 5sp. Have not tried a 6sp Sequential yet. My mate who used one advise me that

they are high maintainance item. Interested to have a go.

Alex 0433559972 or PM me

a lot of them have been used in race cars because of there direct drive, strength and speed of gear change. Can you tell me what part of a race car ISNT high maintenance....lol if you want to play with the big boys you have to spend the money i suppose.

luckily this box was used on street, just for high speed passes. so is in good condition.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...