Jump to content
SAU Community

Recommended Posts

Guest RedLineGTR

get it done asap...since when it goes fully then u will be towing your car to the workshop. if its also leaking on the belts etc that isnt good kills the life of them. While driving to the workshop make sure the water level in the radiator is okay the last thing u need it to overheat the engine. But this depends on the leak.

Link to comment
https://www.sau.com.au/forums/topic/25958-r33-water-pump/#findComment-550095
Share on other sites

Guest RedLineGTR

oh thats not too bad..but yah if ya can get it done asap..Some people water pumps just go nearly in one go...and then time to tow. Also think about if u need anything else done maintenece wise..since while they are doing that other things can be done..less labour etc. Cheers Rob

Link to comment
https://www.sau.com.au/forums/topic/25958-r33-water-pump/#findComment-550108
Share on other sites

My water pump started leaking after i flushed my radiator. Didn't leak much the first day - 1 hour after i got my car to work the next day it had lost almost all of the radiator fluid. Lucky the workshop i take my car to is 25meters up the road. Had the timing belt replaced at the same time. $500 all up with new coolant. I'd get it done ASAP kaotik

Link to comment
https://www.sau.com.au/forums/topic/25958-r33-water-pump/#findComment-550704
Share on other sites

Originally posted by Hicks

My water pump went not so long ago.

Buy a vl turbo water pump. It'll cost about $100 bucks. Don't let them get a genuine one, you'll be lookin at between $400-$500 bucks!!

I have done this very thing and regeret it,

The r33/r32 pump has one bolt hole in a different place to the vl pump and over time because the pump isn't bolted down hard in one place it will start to leak, in fact it took 2 months on my car if I had put the covers on over the cambelt I'd never know. as the leaking water never gets to the road (evaporation?).

I payed $76 for my vl pump.

I'm currently looking at getting my origanal pump repaired with new seals and bearings (about $40 in parts and labour).

(Excuse spelling errors. I'm not very well today)

Regards

Damqik

Link to comment
https://www.sau.com.au/forums/topic/25958-r33-water-pump/#findComment-550712
Share on other sites

The stock pump has 9 fins, not 5 :P But they are smaller. Apparently 6 big fins flows better than 9 small ones. Actually, it may not, it might just have less of a load on the engine and thus less power loss.

Link to comment
https://www.sau.com.au/forums/topic/25958-r33-water-pump/#findComment-551732
Share on other sites

yeah thats what i thought/heard, and cavitation only comes with really high revs with the standard gts-t pump, higher than 7000. The n1 would be suited only to the gtr, as it revs higher, unless you raised the revs on a gts-t. So basically, i dont think there is any point getting and N1 pump for a gtst, although it does sound good :P

Link to comment
https://www.sau.com.au/forums/topic/25958-r33-water-pump/#findComment-552629
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...