Jump to content
SAU Community

Recommended Posts

Hi guys,

I'm running a stock turbo in my gts-t r33. I wanted to set my hi setting to 11psi.

How can i tune my profec B II for 11psi???

Help greatly appreciated.

hey mate i hooked one of these up on a r33 last week. basically just turn the knob to increase the boost thats the set gain. its in % so stock is 7psi on a r33, at 0%. 10% should give you 7.7psi 20% 8.4psi and so on.

adjust the gain if your boost trails off at high rpm by default its 5% i think. i only needed to have 7% of gain

honestly just play with it a couple of % at a time with a mate in the car and find a nice open piece of road

REMEMBER: DONT BREAK THE LAW

your boost settiing is reliant on the percentage that you dial in, this will adjust your solenoid to open at a particular boost level. for 11psi you will need about 22-25% on a standard turbo. all you do is when its on turn the chrome knob to select the % thing. when u do this you will also have to change your overboost, hit select til it comes up red with either a Bar reading or number, ie:100. 100 represents 10PSI as it wont have the decimal place value. so 112 means 11.2psi. now this setting will probably want to be set around 120 or 0.85bar, watever values you have being displayed (ie:Psi or Bar). What this does is cuts your boost by a percentage that you have elected in the other settings. 10% will be fine for the overboost cut value. finally your gain is to help the response of your turbo spooling. it goes between 5% and 25%, the higher you make this the faster its meant to make your turbo spool, the lower the slower but positive aspect is it will help stop your car from overboosting.

hey mate i hooked one of these up on a r33 last week. basically just turn the knob to increase the boost thats the set gain. its in % so stock is 7psi on a r33, at 0%. 10% should give you 7.7psi 20% 8.4psi and so on.

its a percentage of the turbo or wastegates limit. 0% being stock boost and 100% is freeboosting

gain adjusts how aggressive the solenoid is. low gain will make it ease onto boost and drop off in the top end, too much gain will cause it to spike. takes a fair bit of playing around but once you understand whats going on you should be able to figure out what you want for this

start boost or set gain sets the boost at which the solenoid starts to open and feed pressure to the actuator, set this 1-2psi below the boost you want to run, setting it too high will cause it to spike

Hey just had a look at my current settings, havnt been out to play wif em yet.

Hi:

Set: 34%

Set Gain: 65kpa

Warning: 90kpa

L.20%

Cars boosting to 73- 76kpa with this setting. Might lower the gain though, boost comes on to quick.

Just wondering whats the L.20% refer to?

my settings are.... (note: set to psi, not kpa)

low

gain 14%

set gain 75

warning 106

limiter 4%

set 36%

high

the same except,

set 39%

sometimes need to adjust slighty due to temps from night to day.

if someone has better settings for me, plz msg me

my mods are on my lil sig block.

Edited by Jaysiin
Hey just had a look at my current settings, havnt been out to play wif em yet.

Hi:

Set: 34%

Set Gain: 65kpa

Warning: 90kpa

L.20%

Cars boosting to 73- 76kpa with this setting. Might lower the gain though, boost comes on to quick.

Just wondering whats the L.20% refer to?

L20% means if your boost exceeds the set warning level it will drop 20% of your overall boost level ie: if warning is set to 10 and it exceeds this it will immediately drop 20% of the boost pressure (back to 8psi). Problem being if its not correctly set up it will continually jump up and down.

mine is set on 16psi (50%) 15% gain, overboost warning is 17.5psi and the boost cut is set at 7% (L7%). On my application this is perfect.

for everyone running a profec, wat are your settings?

well ill have to check when my engine is back together but the 3 values are 35% 35% and 10psi for the wastgate to open. this gave me a solid 12.5psi in forth gear.

its not an exact science ya just have to play around with it. temp plays a big part in it morning/afternoon so i have the hi/low switch set for the different conditions.

some people have the hi low switch set for different gears also.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...