Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Have a yarn with zenon Josh, Thats about where he's at with some carefully thought out spenshun mods and he has a ball in that flat capper of his.

Yeh might hit him up. My teins gotta go! no question there. Dont even think they are worth trying to save with less silly spring rates in them

T51Z on a stock rb20, and then change the timing belt.

and then fit a new intercooler.

then some more parts.

then wait a couple weeks

RB24 is a waste of time.

Plenty can be done with the RB20. Need to spend a bit on cylinder head work though if you want the numbers and torque.

Leave the bottom end for now, take off the head and put on a pre-ported one with bigger valves etc. Go Pon cams, Angry German with surge tank injectors and a NISTUNE or I have an ECU in my 20 which has already been chipped and I won't be needing it. Already set up for 550's and a Z32AFM

I can't use AFM with the new setup as there is nothing big enough for 1rwkhp

So all you'd need would be injectors, fuel system, JJ intercooler and a couple of other bits and pieces. Could easily get 220rwkw on that turbo.

Then when you can afford more of an upgrade (or even want one) do the cylinder head and go bigger turbo/cams. You can make 235rwkw on the stock cams with stock/untouched head.

You can also do 205-210 rwkw on stock injectors and AFM too but I would be careful running them at those levels.

Plenty can be done with the RB20. Need to spend a bit on cylinder head work though if you want the numbers and torque.

Leave the bottom end for now, take off the head and put on a pre-ported one with bigger valves etc. Go Pon cams, Angry German with surge tank injectors and a NISTUNE or I have an ECU in my 20 which has already been chipped and I won't be needing it. Already set up for 550's and a Z32AFM

I can't use AFM with the new setup as there is nothing big enough for 1rwkhp

So all you'd need would be injectors, fuel system, JJ intercooler and a couple of other bits and pieces. Could easily get 220rwkw on that turbo.

Then when you can afford more of an upgrade (or even want one) do the cylinder head and go bigger turbo/cams. You can make 235rwkw on the stock cams with stock/untouched head.

You can also do 205-210 rwkw on stock injectors and AFM too but I would be careful running them at those levels.

Is it worth toying with cam gears? Or not worth it unless I went to a full ECU?

Worth my time buying a 6boost manifold for the current turbo? (I have no views of going high mount/ex gates).

The key is, response, keeping it alive and staying consistent

Is it worth toying with cam gears? Or not worth it unless I went to a full ECU?

Worth my time buying a 6boost manifold for the current turbo? (I have no views of going high mount/ex gates).

The key is, response, keeping it alive and staying consistent

No, stay factory manifold but maybe heat coat inside and out.

easy to keep it alive but revs will have to be cut short at 8k until you can afford/want bottom end work. And I'm not talking about beat kind of bottom end work.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
×
×
  • Create New...