Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Hey hey hey com on now I showed and offered but had no takers :P

PS. This new cupping rumor is nuthin but that. Ive learnt my lesson and therefor will never promise cupping again :P

The deal was for modified car + cupping.

You turned up in one of these:

Shopping-Trolley-A1c623.jpg

:down::);)>_<:down: :down: :down:

30mm spacers i see?

They are a bit like dog's balls aren't they? lol

Hopefully not as obvious to our friends in blue, davey boy!

Or at least those bastards with purple lights on the roof :down: cops MIGHT let you off with a warning if they see them. Transport will just start to lube up :)

Yeah I thought it would be too but it just arrived 10 minutes ago and it is looking like the worst piece of engineering I have seen in a while. The twins have been done nicely but the rest of it is hell messy. The fuel system and boot battery are neat but engine bay...yuk. It serves a purpose though, I guess. And with over 600hp at the wheels it serves it well.

It's Josh's old car btw

BAM!

That car went to hell when it went to WA

86808747xXNzAv_ph.jpg

now :down:

enginebay.jpg

For those playing at home,

The car was the most mint S13, every single trim part still there + air con, pefect streeter, drive to willow bank, 10.8's, drive home.

Got turned into a back yard tracker.. Kinda thing when it was sold

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...