Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

brandon,

just checked this pic, it was uploaded on cruisingbrisbane from thursday @ harry diner, buahahah car is dirty, nice cameras show the dirt even more loool

post-47576-1259577552_thumb.jpg

hey mang, sorry didnt reply your pm, f*kin sau limit shit, but yeah its all boring shit atm. wat spec on ya rims? size / offset etc?

reading the mail never felt so good :)

you got work tmr at 1 again man? or usual at 630?

back to the usual but might have another late start this week. i like night shift :D

hey mang, sorry didnt reply your pm, f*kin sau limit shit, but yeah its all boring shit atm. wat spec on ya rims? size / offset etc?

hey mate,

its all good, do tell me if u need a hand, fackin bored all day , rims i think are Advans Ra3-DT 18x10 +19 wrapped in nankang 255's all around, apparently very very rare rims, were on the car when i got em, hated them but kinda grew on me, planing on work emotion xd9 18 x 10 + 18 soon in white,

what are you doin to the 32?

Edited by brizzy_rocker
back to the usual but might have another late start this week. i like night shift :D

well let me know you sly dog and we'll do some work on the 32 :)

hey mate,

its all good, do tell me if u need a hand, fackin bored all day , im not sure about rims, but i thnk theyr 18x10 +19 wrapped in nankang 255's all around, apparently very very rare rims, were on the car when i got em, hated them but kinda grew on me, planing on work emotion xd9 18 x 10 + 18 soon in white,

what are you doin to the 32?

volk gtc's!! do it do it

and the question is, what isnt dave doing to the 32... :D

what are you doin to the 32?
and the question is, what isnt dave doing to the 32... :D

not much, just a few little things...

when u get ur new rims you gotta aim to fill the guards up, and then put a little roll on them. then make em look the shit. like so...

PB290009.jpg

haven't finished yet, but looks the jizz.

Edited by 32_Dave

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
    • Yeah - I mean, go the other way. Smaller range. Not larger.
×
×
  • Create New...