Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Grrrrrrr can't get damn cat out..... it's held in well with studs + bolts. Got the bolts off but the studs it seems are welded to / are a part of the cat.

Any tips?

Do I have to remove the whole back section of the exhaust to get the cat out? I think I just realised this to be true :P

just work with the wiggle room

exhaust is on hangers, should be able to move it back a bit to get the cat out

its a c*nt of a job on my car, thats why i decided i wasnt going to swap the decat pipe in every track day after doing it once

LOL, found dad's old paperwork for the ride on:

He bought it second hand in 1994, and it was old then:

rideon1.jpg

'twas an 8HP apparently (I thought it was less) but that engine blew up.

He bought the new 10.5HP engine in 1998, at the time it was the biggest one we could get that fit:

rideon2.jpg

I'm not sure how old the mower itself is exactly but I did find the instruction book:

rideon3.jpg

If you look down the bottom, you can note the SIX DIGIT phone number.

Now I remember going from 7 to 8 digits some time in primary school, but 6?

Some quick research, and this very informative page tells me that "Brisbane went to 7 digits in 1975". Therefore, we can conclude that the beast is older than 1975. Thats 35+ years!

And note: it is a mini tractor, not a ride on :P. EEESSSSSSS AAAAAAAAAAAAAARRRRRRRRRRRRRRRRRRRRRRRRR!!!!!!!!!!!!!!!!!!!!!!

Look, you can (could) even get tractor attachments for it:

rideon4.jpg

Definitely needs turbo love

Don't talk to me about ride on trailers, made that mistake once, hung over after new years, we decided to ride in the trailer to clean up the mess we made couldn't find the holding pin to keep it on, going down the hill very fast and the trailer popped off, catapult anyone?

Don't talk to me about ride on trailers, made that mistake once, hung over after new years, we decided to ride in the trailer to clean up the mess we made couldn't find the holding pin to keep it on, going down the hill very fast and the trailer popped off, catapult anyone?

bugger

we could MAKE a trailer for it

matter of fact, there is a small box trailer in the back yard I doubt has any chance of ever getting road registered. Could convert it to a tractor trailer

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Thanks. We getting some parts along too so he will be solving the speed issue like next week so i will let you know what he came up with.   
    • 21 is explicitly the coils detected as the issue. Is it guaranteed the actual issue? No. Just the ECU thinks it is. When you say rattling, describe it better, get an audio clip as best you can if possible.
    • Yea got me coppers. Bad news is I just put them in and the car still has the light and shakes. I also noticed I hear like rattling coming from the exhaust piping right under me. Does 21 also have a possibility of being O2 sensors?   So, coil packs are good, the harness is good, the MAF is working, and obviously the spark plugs just replaced and working.
    • Make sure you drop the GTT base tune back in, and set your injectors again, this will remove anything playing up with it you may have removed. Possibly lean there as it's normally a fast transient going THROUGH atmospheric pressure, and a turbo motor would then quickly go richer as boost builds. The only worry you MIGHT have is ignition timing, as the DE is higher compression than the DET from memory. But again, you're not in boost, so the DE motor will be a lot more forgiving at atmospheric.   Get Murray, Kinkstahs, and Johnny's input on tuning haltechs, those guys have played with tuning enough in the past to be able to help now you're past the trouble shooting stage of the MAP issue
    • @Rusty NutshI mate. Do you have a pinout diagram for the na neo auto ecu? 
×
×
  • Create New...