Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

:cool: there are no other pics so far - and i dont think there are any more coming, so more in a month hopefully!

and martin i wont be there thursday - i blew a heater hose, so i that needs to be replaced before i can driver her, dan is coming around thursday arvo to have a look

apparently if its f**ked really bad you gota lift the motor to get to them :blink:

so fingers crossed dan can work some magic - lol no pressure

and martin i wont be there thursday -

WEAK

dan is coming around thursday arvo to have a look

ORLY? When is he going to weld wield my mower then?

apparently if its f**ked really bad you gota lift the motor to get to them :blink:

so fingers crossed dan can work some magic - lol no pressure

This is why rule no 1 when doing an engine swap is: New heater hoses. They don't cost much and are much easier to do while you are changing engines

Edited by Smity42
This is why rule no 1 when doing an engine swap is: New heater hoses. They don't cost much and are much easier to do while you are changing engines

I shall remember this for Susan two point five

This is why rule no 1 when doing an engine swap is: New heater hoses. They don't cost much and are much easier to do while you are changing engines

agree. when we went to put in annas engine i looked at the position of the hoses and instanty went to buy new ones lol

ps 2 full days learning about sewerage is enough....but alas i have one more full day tomorrow

I can school you up about sewerage. What do you want to know ?

ORLY? When is he going to weld wield my mower then?

This is why rule no 1 when doing an engine swap is: New heater hoses. They don't cost much and are much easier to do while you are changing engines

agree. when we went to put in annas engine i looked at the position of the hoses and instanty went to buy new ones lol

hahah yeeeh - didnt even think of it to be honest at the time, but yeh totally wishing i'd replaced them hahaha

oh well

and yeh martin dan loves me more :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...