Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Sorry for absence. I've been trying to restore 700 gig of files from a crashed hard drive, and dig through stuff for money to get those Advans.

Fun. I lost a 3.5TB RAID array once. only had about 2TB of stuff on it but, and I managed to get most of it back. Lost a few movies and TV shows though :(

Many days of data recovery efforts there.

Fun. I lost a 3.5TB RAID array once. only had about 2TB of stuff on it but, and I managed to get most of it back. Lost a few movies and TV shows though :(

Many days of data recovery efforts there.

Yeah, still going on my revcovery. Looks like I'm going to lose all my movies though, it won't transfer anything larger than 600mb. Slowly salvaging my tv shows and songs. one file at a time....

you're killing me marto

<3

This forum fails harder than an SR with gay purple cam covers :)

I post, I wait 10 minutes for it to time out, go back to find my post twice. Epic fail :(

You watch, this one will do it too...

you're killing me marto

<3

This forum fails harder than an SR with gay purple cam covers :)

I post, I wait 10 minutes for it to time out, go back to find my post twice. Epic fail :(

You watch, this one will do it too...

Yeah, still going on my revcovery. Looks like I'm going to lose all my movies though, it won't transfer anything larger than 600mb. Slowly salvaging my tv shows and songs. one file at a time....

Recovering the RAID array was even more balls - had to de-stripe it with 6 good drives and one partially failed drive (out of 8 drives, 1 failure was recoverable but I lost 2), and not knowing what order the striping was done in :(

Yeah, still going on my revcovery. Looks like I'm going to lose all my movies though, it won't transfer anything larger than 600mb. Slowly salvaging my tv shows and songs. one file at a time....

Recovering the RAID array was even more balls - had to de-stripe it with 6 good drives and one partially failed drive (out of 8 drives, 1 failure was recoverable but I lost 2), and not knowing what order the striping was done in :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...