Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

What

The

F_ck

Woman set on fire during surgery

Happy John :D

Fire, solves everything.

fix it... making brain hurt

Fixed:

I say, old chaps, I do appear to be suffering some minor homosexual tendencies when posting on this fine forum. My browser of choice is the fabled Internet Explorer but alas, when I submit a post it appears not once, but twice! It's just not cricket.
Edited by Smity42

Stoopid pintaras...

Got home from work yesterday and noticed my brake lights were stuck on :D. Don't know when it started, but presumably it was yesterday sometime or my battery would have been flat yesterday morning.

Fortunately, all the inconsiderate, uneducated, and generally incompetent drivers of Brisbane somehow managed to avoid running up my a*se despite having no indication of when I was stopping :bigthumb:. Good job, team!

So I got out my multimeter ready for some HK electrical diagnosis. After doing some Houdini tricks I managed to unplug the switch that triggers off the brake pedal. Lights go out. Then I used a bit of wire to bridge the contacts, lights come back on. That settles it then: the switch is faulty. Out I go to the ute, perform some even more impressive Houdini tricks (since it is parked beside the house and you can’t open the driver’s door) and manage to get the switch out of it. Back to the coupe, but as I go to remove the switch from it, I notice that there is a hole in the brake pedal where it should be triggering the switch. So basically, the pedal is not actually pressing on the switch. Well that explains it, there’s obviously meant to be something in that hole. I found half a dozen pieces of rubber in the foot well that almost re-assemble to form a rubber stopper. That would be it! BACK to the ute now, more Houdini tricks to remove that rubber stopper this time, then again to put it into the coupe. Fixed!

Profit.

Im here ... Does that count or have I been kicked out for my lack of presence at the BnR meets :)

No, but if you don't start turning up again soon you will be! :D

Good morning!

mang.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Just a thought, was that car and auto at any point of its life? If so, maybe whoever bridged the inhibitor switch/circuit did a not so good job.
    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
×
×
  • Create New...