Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

Hello all.

how was the weekend? Mine consisted of 'Pain da fens... up, down, uuuuuuuup, dooooooooooooooown......'

McRae - backstreet boosting in an unrego'ed car? noice

McFly - The federal 535 is a pretty quick street type tyre. Don't expect too much from them. Not saying they're not grippy, but they are not a flash tyre. Good to hear that your wheel was fixable.

Mr Marine chronometer - Did you sort out your misfire problerm???

Hello all.

how was the weekend? Mine consisted of 'Pain da fens... up, down, uuuuuuuup, dooooooooooooooown......'

McRae - backstreet boosting in an unrego'ed car? noice

McFly - The federal 535 is a pretty quick street type tyre. Don't expect too much from them. Not saying they're not grippy, but they are not a flash tyre. Good to hear that your wheel was fixable.

Mr Marine chronometer - Did you sort out your misfire problerm???

Lol I considered putting the 31 plates on it but then just decided f**k it n went without plates. I want it back on the road now though lol :D

Just spent 3.5 hours inspecting a wall with the engineer. f**kin gay.

No one ever said that these walking gant chart guys were employed for having any relevant knowledge! (including maths, or the ability to read gant charts)

Walking gant chart man just asked why my hours this week were less than last week, when in fact i did 1 hour more :D

Clearly he is deducting hours spent on SAU as non working lol

No one ever said that these walking gant chart guys were employed for having any relevant knowledge! (including maths, or the ability to read gant charts)

Yeah PMs are there to make everyone else hate life.

Martin - yes 535s are good street tyres.

I have stolen coil pack 1 and 2 and the loom from your ute. I covered it back up again. Haven't put any other parts into it yet because it 1. may not be the problem. 2. I need a vacuum to get all the leaves out so I can put things back where they came from. and 3. I dropped a screw and need needle nose pliers or a magnet stick to get it out.

Edited by Isola

nah it was sitting there behind the 31, just got moved to mine yesterday, will need to make some time to work on that thing too.....

Martin - yes 535s are good street tyres.

I have stolen coil pack 1 and 2 and the loom from your ute. I covered it back up again. Haven't put any other parts into it yet because it 1. may not be the problem. 2. I need a vacuum to get all the leaves out so I can put things back where they came from. and 3. I dropped a screw and need needle nose pliers or a magnet stick to get it out.

I have an extendable magnet stick thingo if you need to use it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I'll get one of these also just for giggles
    • I bought 6 new spark plugs to compare readings. They will be here tomorrow and ill see if meter is far off if it all. I know one is at least reading 0 so its best replace all anyway if one is bad, from experience. I still have to test the harness just to be sure its not a double issue and I waste my time haha-the old plugs are iridium I always thought those lasted more than 50,000 km.
    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
×
×
  • Create New...