Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

I wondered what that text message was about, Joe :P

That car came apart surprisingly fast too! Did it go back together as quickly? :)

Haha well i dunno how long it took you lol but there were 4 of you!

Felt stupid this morning when i didnt realise thats where u had been last night lol the widscreen wipers were the hardest because i had to get em on the splines on the right position agen lol

Took me a couple of minutes to find the lead off the distributor (F**KERS! LOL) I checked the fuse box first

Finally found the hot ranga that i know! Hair doesnt look that red there but it is

WIN!! invite her to baskins next week wether its the same one or not lol

surely it's close? Morning Mangs,

Strayen day today need to get uni assignment finished. I don't think it fully qualifies as a strayen day though.

That reminds me I need to pre-book some not-quite-strayen days for the mondays after the last two F1 rounds...

Why is this?

Why is this?

The penultimate race is on at 2 in the morning or some shiz and I don't want to go to work the next day. Also it's the day after my birthday.

The last race is on an hour later than normal (which is already too damn late when you start work at 7am), and there will be much drinking and celebrations when Mahk Wibbah wins the WDC. So once again, don't want to go to work the next day.

But two Mondays in a row as 'strayen days would raise too many eyebrows, so I'm just going to take leave. I have sh*tloads anyway.

Strayen day today need to get uni assignment finished. I don't think it fully qualifies as a strayen day though.

Is there beer available?

Thanks Dan for coming over yesterday to try and get these studs out... no luck though. So right now I need to organise:

1) New battery

2) Tow to workshop

3) Workshop replaces studs/hubs/whatever is needed

Yayyyy

Is there beer available?

Thanks Dan for coming over yesterday to try and get these studs out... no luck though. So right now I need to organise:

1) New battery

2) Tow to workshop

3) Workshop replaces studs/hubs/whatever is needed

Yayyyy

Can possibly assist towing with sexF if you need... You'd have to hire a trailer though

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Don't assume too much when there is a voltage issue....if the battery is flat and the alternator not charging it is easy for the voltage to drop way low at the ECU due to the draw of stuff like coils, fuel pump etc Whatever you see at the battery with the motor off, it should be at least 13.8 with it running
    • I have been wondering if this is as simple as a voltage issue with the battery. Even on a charger, I can’t seem to get it over 11.8V on the terminals.    Unless the alternator has failed as well, that wouldn’t cause it to die in the middle of driving though. 
    • I’ll give this a shot next time I’m able to wrench on it.    I was able to get my hands on a Haltech Nexus, so that should help with some of the more bizarre troubleshooting. Make sure the CAS is actually sending signal and will be able to set the proper dwell on the R35 coils.    I’ve checked power/grounds/signals at the CAS, ignitor, and plugs and it was all there. Granted this was static with ignition on, not cranking.    I also plan on swapping out the fuel filter and throwing on a fuel pressure gauge at the rail just to confirm I’m getting the correct pressure at the rail. 43psi if I recall correctly. 
    • The attached document is fine. I just downloaded & opened it.
    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
×
×
  • Create New...