Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

West side sau peeps wats goin on!?!? :P just wanting ideas for areas around brisbane that would be good to run in a new engine??? any ideas?? i should hopefully be getting my car back this week after its run in tune's done so on the weekend i can get started on the 1000kms haha. besides nebo.

Edited by 8znR33
West side sau peeps wats goin on!?!? :P just wanting ideas for areas around brisbane that would be good to run in a new engine??? any ideas?? i should hopefully be getting my car back this week after its run in tune's done so on the weekend i can get started on the 1000kms haha. besides nebo.

get someone to do it on the dyno, easier and probably cheaper

get someone to do it on the dyno, easier and probably cheaper

dunno if it will be cheaper on the dyno, i knw with the run in u need to put load on the engine e.g. hilly areas but i think it would cost a bit to run it in on a dyno. i dont mind the driving will be fun :) i gotta get use to my twin plate and i want to play around with my sequential shifter :P

dunno if it will be cheaper on the dyno, i knw with the run in u need to put load on the engine e.g. hilly areas but i think it would cost a bit to run it in on a dyno. i dont mind the driving will be fun :) i gotta get use to my twin plate and i want to play around with my sequential shifter :P

I admire your enthusiasm, I fkn hate running in engines. Our last engine only took a few hours to run in, you can make the dyno mimic a bigass hill by setting a large ramp rate!

sequential? must be a pretty serious 33. What are the specs on the engine?

i wouldnt say too serious i just bought the ikeya formula sequentil shifter that bolts straight to the stock gear box, but its a 25/30 but with stock head, bought the block with hypertic (dunno if thats correct spelling) pistons was going to change em but had to pay for other things so just kept em but all brand new bits with a t04z with the usual supporting mods :P

I admire your enthusiasm, I fkn hate running in engines. Our last engine only took a few hours to run in, you can make the dyno mimic a bigass hill by setting a large ramp rate!

hehe yea i havent been driving my 33 in a while kinda miss it so i dont mind doing the run in drive. yea could get the tuners to do it but i rather save the extra costs to be put to the full tune :P

im burnt and i did smell like fish (that's what she said)

i caught some fish though, so it wasnt a fail day at all

im burnt and i did smell like fish (that's what she said)

i caught some fish though, so it wasnt a fail day at all

but did you get any scrabble ?

sup mother b1tches

back at work today :yes: and they are busy installing ie8 on my PC :D

and I seem to have lost my ID card over the holidays :happy:

Damnit noooo!! minimum age to hire a GTR in the UK is 28! I'm a year out >.<

that sucks mang

sup mother b1tches

Sarrrpp yourself

back at work today :woot: and they are busy installing ie8 on my PC :D

Yeah..... that'll take a while :yes:

and I seem to have lost my ID card over the holidays :happy:
that sucks mang

You took the words right out of my mouth

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Just a thought, was that car and auto at any point of its life? If so, maybe whoever bridged the inhibitor switch/circuit did a not so good job.
    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
×
×
  • Create New...