Jump to content
SAU Community

Recommended Posts

  • Replies 207
  • Created
  • Last Reply

Top Posters In This Topic

SKYBEE - your lucky to have black. any colour will suit it.

BLUE RED GREEN PURPLE AQUA.

just click the link above to see a picture of the blue kit.

if anyone is interested please feel free to email me at

[email protected]

and i will do my best to help you out.

  • 4 weeks later...

Never thought I'd say it, but i'm interested too.

Could you please shoot over any more pics and info you might have. I think Blue ones will go best on my silver R33

Thanks...

[email protected]

i know the bloke that owns the white skyline.

hes very happy with his neons.

melv, did you used to own that white commodore vt or somthing with trippy looking rear lights?

Hey champ,

yeh i used to own the White VT (02DEF)

then i owned a White VXSS (SIR VX)

and now i own a White R33 GTR ( havent got plates yet )

will have to meet up with u champ i rember u from the BWCC FORUM etc.

i never thought ide add neos either but hell

im sold!

i live in brisbane, so once i get new wheels for my baby ill be driving to the goldcoast to come see you!!

now i just need to decide.. Blue or Red

ahhh!

silver skyline hmmm

hehe blue it is

so whats the fitting like?

cause im getting new bodykit fitted and some other little things done over the next few weeks.

Whats do you think would be sufficient for an r33 gtst, do i want 4ft ones for front and back and 5-6ft for the sides? If im going to do it i mite aswell do it right :)

how much would that be?

1.2m sides

1m front

80cm rear (coz of your exhaust)

that kit will be $200 - $220 inc courier.

fitting is very basic. drill two holes and cable tie them up to the side skirts or if u want it done right, drill into the bottom lip under the side of your car hold the neon on the inside of lip and cable tie it into place easy as that really !!

hey mate,

u get a transformer that u can mount in your engine bay or hide it somewere and from that u have 4 wires

two thin which are black and red red goes to your switch in the cabin and the black to a negitive

there are also TWO fat cables both a positve and it needs to run in a circle type circt under the car.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I thought it could be an issue because the standard plate was flexing when stressed. Maybe the original gear set will hold a bit better without flex? Last time on the dyno it made around 670nm at the hubs. Now it have bigger turbo and better intake but have not been on a dyno yet. The car is being used from family trips to drag race events. So the shifts can be a little violent. It is grinding if I shift to fast so was thinking I should overhaul it soon.
    • From the factory on RB26s there's a fitting on the intake manifold collector/"plenum" that provides pre-throttle boost signal. That's how they did it back in the day, I figure it's fine to replicate it.
    • I would be surprised if that wasn't the issue. It's probably telling you, that even if you remove the plastic liner, you may have some other clearance issues that may occur too in some scenarios. IE, tyre to guard. It looks like someone has already rolled the lip, but you may still have issues in the future IE, turning and hitting a bump etc. The fact it changes how bad it makes the noise when you are going backward vs forward is highly indicative that it's the tyre rubbing. They do make a terrible sound, even if you're only pushing a project car that has a liner hanging down on a tyre!   Has the car been lowered? If it has been, what is the measurement from the centre of the wheel hub to the lip of the guard straight up?
    • Summernats cruiser?
    • Mark's a bit smarter than people give him credit... He'd convince the person that is to become dead, to drive him to the forest first. That way his car has no evidence in it, and he's free to dispose of their vehicle permanently how he sees fit too...
×
×
  • Create New...