Jump to content
SAU Community

Recommended Posts

Hey guys.

I have read up on how much boost a R33 stock RB25 turbo can handle. As I have one.

I had my car tuned at 13psi making a generious 291 rwhp. I have a AEM Electronic boost controller.

So I run it on 12 psi seeing as I gather that 14+ the turbo is likely to fail.

So I was driving my car this morning at 9am. I let it idle warm to 70 deg C and then took it for a drive. Air was super cold from yesterdays rain.

When I was boosting the car was reading 15 and 16 psi a few times and then as I continued to drive for 10 minutes it would level out at 12psi again.

So I am wondering if my turbo surges or spikes to 15-18psi every so often on cold mornings or nights, up hills or in high gear. Will the turbo explode soon?

Cos I don't want to feed my turbo some compressor wheel peices.

Thanks in advance

Berny

its not ideal. Id get it sorted out.

And your turbo wont be fed a compressor wheel. It is the compressor wheel :P Maybe you mean engine haha.

hahaha yeh, typo. Meant, I don't want to feed my engine compressor wheel pieces.

I used to get that on my stock turbo.. MS-IBC boost controller set to 7/10psi.

On low boost on a cold night/morning it would creep up to around 9psi initially but settled to 7psi spot on..

on high boost it would initially creep to 13psi but it would settle down to 9-10psi rock solid once the ebc discovered it was creeping.

The other thing i used to do was decrease the gain a wee bit to help.

If your turbo creeps to 14psi and STAYS there, then possibly you havent fine tuned it and thus would need to decrease the GAIN/Start boost.

You def dont want to run 15-18psi otherwise:

1) Turbo's exh wheel WILL break

2) You will hit mass over-run and the ecu will do weird shit to save the engine

Oh. The boost controller must be allowing the wastegate to open later to run higher boost. But when the air is cold/dense and the intercooler has not soaked up heat, then the boost creeps. The EBC then realises it and settles it back down to correct setting.

How do I decrease the gain?

Nah for like 5 or so full gear runs the boost was at 16ish. Then it got better and sat at 12psi.

Turbo's explode purely due to hoop stress if they are ceramic, not because of heat or dirty oil. Just because they are spinning too fast and to much energy.

So if my ecu stops the car from leaning out. The turbo can still explode cos the ECU won't stop the turbo spinning too fast

Any other input into this?

I wanna know how serious it is running 15-18 psi when engine is cool and if turbo will explode. Or not.

Otherwise I will definitely get a 2535 or 2835 or GTRS really soon.

Dammit, so much money :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...