Jump to content
SAU Community

Recommended Posts

Hey guys.

I have read up on how much boost a R33 stock RB25 turbo can handle. As I have one.

I had my car tuned at 13psi making a generious 291 rwhp. I have a AEM Electronic boost controller.

So I run it on 12 psi seeing as I gather that 14+ the turbo is likely to fail.

So I was driving my car this morning at 9am. I let it idle warm to 70 deg C and then took it for a drive. Air was super cold from yesterdays rain.

When I was boosting the car was reading 15 and 16 psi a few times and then as I continued to drive for 10 minutes it would level out at 12psi again.

So I am wondering if my turbo surges or spikes to 15-18psi every so often on cold mornings or nights, up hills or in high gear. Will the turbo explode soon?

Cos I don't want to feed my turbo some compressor wheel peices.

Thanks in advance

Berny

its not ideal. Id get it sorted out.

And your turbo wont be fed a compressor wheel. It is the compressor wheel :P Maybe you mean engine haha.

hahaha yeh, typo. Meant, I don't want to feed my engine compressor wheel pieces.

I used to get that on my stock turbo.. MS-IBC boost controller set to 7/10psi.

On low boost on a cold night/morning it would creep up to around 9psi initially but settled to 7psi spot on..

on high boost it would initially creep to 13psi but it would settle down to 9-10psi rock solid once the ebc discovered it was creeping.

The other thing i used to do was decrease the gain a wee bit to help.

If your turbo creeps to 14psi and STAYS there, then possibly you havent fine tuned it and thus would need to decrease the GAIN/Start boost.

You def dont want to run 15-18psi otherwise:

1) Turbo's exh wheel WILL break

2) You will hit mass over-run and the ecu will do weird shit to save the engine

Oh. The boost controller must be allowing the wastegate to open later to run higher boost. But when the air is cold/dense and the intercooler has not soaked up heat, then the boost creeps. The EBC then realises it and settles it back down to correct setting.

How do I decrease the gain?

Nah for like 5 or so full gear runs the boost was at 16ish. Then it got better and sat at 12psi.

Turbo's explode purely due to hoop stress if they are ceramic, not because of heat or dirty oil. Just because they are spinning too fast and to much energy.

So if my ecu stops the car from leaning out. The turbo can still explode cos the ECU won't stop the turbo spinning too fast

Any other input into this?

I wanna know how serious it is running 15-18 psi when engine is cool and if turbo will explode. Or not.

Otherwise I will definitely get a 2535 or 2835 or GTRS really soon.

Dammit, so much money :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...