Jump to content
SAU Community

Sr20 Red Top

dodgybrooks
 Share

Recommended Posts

dodgybrooks Community Regular

dodgybrooks

Posted
Posted

SR20 red top, suit rebuild. Loom included. One of the coilpacks, cas, oil pump and sump is broken. Will supply brand new oil scavenger. Turbo OK. $500

Located Mt Gambier, SA. Can organise free freight to Adelaide, other locations buyer pays. Call 0435 281 536. Don't expect prompt replies if you PM or SMS.

post-18999-1237859169_thumb.jpgpost-18999-1237859319_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/262452-sr20-red-top/
Share on other sites
dodgybrooks Community Regular

dodgybrooks

Posted
  • Author
Posted
so apart from the coilpack, cas, oil pump and sump, is there anything else wrong with it? whats it been in a crash?

will new parts bolt back on or will it be interesting lol

Oil pump died and the car sat idling for about 30/45 min before I realised. Drove it home about 70kms and was fine, no noise from bearings and boosted fine but I changed it with another red top that was lying around at a mate's workshop. Then the engine sat around for a while out of the car and water got into the valley and ruined a coilpack. CAS was swapped out and sump was damaged in the container on the way home from Japan.

Nothing else wrong with it as far as I know. New cas, coilpacks, oil pump, 5 min with a hammer on the sump and you'd probably have a good SR20 for cheap, but then again the bearings might be shot, cams scorched, etc..... who knows, hence the cheap cheap price. The fact that it ran fine afterwards says that it probably isn't all that damaged.

Link to comment
https://www.sau.com.au/forums/topic/262452-sr20-red-top/#findComment-4495575
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Chupapy
      Coolant leak?

      By Chupapy · Posted

      Is it alright to top up with just another green coolant?
    • Songo
      New kid on the block

      By Songo · Posted

      thanks GTSboy. My confusion at the moment is i am trying to locate the ignition, ECU battery power and the ECU negative The closest thing i can find is the for the S15 on Page 8 of the Wiring Specialties web page https://drive.google.com/file/d/0B9F33_M_GgENQnZ6STMxVmVNd1E/view?resourcekey=0-eZ4nNRwRoqa1qvKlWWHm8A I cannot find the same diagram for the R33 RB25DET Series 2 dash plug pin out.... Do you know what the Pins? or know where i can find the same pinout diagram for the RB dash plug? Thanks for the advice on the box... i like a 6 speed so might be on the lookout or the box now.. a topic of discussion for another post...
    • Chupapy
      Coolant leak?

      By Chupapy · Posted

      Will have a look at that. I cant see any leaks 
    • GTSBoy
      Coolant leak?

      By GTSBoy · Posted

      Put another overflow bottle (ie, a 1.25 coke bottle or similar) under the overflow hose and see if it is being pushed out there or if it is disappearing into the engine.
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      Staring on a stand is no issue. You just have to wire everything up, give it fuel and cross your fingers that the stand is robust enough. Arranging the inlet plumbing is often the hardest part, without any surrounding structure to hand some of it from. No need for coolant if you only want to run it for <1 minute. As to the gearbox - I think the little Aisin box is a bit stronger than the other small Nissan boxes that went behind SRs, but I wouldn't be too keen to test its limits with the torque of a boosted 25. I don't know if you can retain the box and the tailshaft. The box won't connect to the RB without an adapter of some sort, which is either a plate that will push the engine forward (which is not good for fitting it into the bay's available space) or push the box back, which messes with the box position and tailshaft length - OR - cut and shut work on the bellhousing, which is a long way from "least modification". I'd be buying a new 370Z 6 speed or similar, doing what has to be done to that to make it fit RB (ie, cut and shut bellhousing) and the requisite tailshaft custom/mods.
×
×
  • Create New...