Jump to content
SAU Community

Recommended Posts

sounds like you have more than one problem probably began just needing a good tune explaining some smoke and being laggy, (not sure why your really pushing a fresh engine too hard either, but anyway) but since pulling pipes off and cleaning then putting them back on im sorry to say this but i think you have a cooler pipe leak or something now too, ive had very similar problem in the past, only to find after many hours on a dyno and removing replacing removing replacing the front bar and many other hoses there was one hose that was starting to strech open just as it was comming on boost. it would richen wright up and obviously stop making boost.

when the car was at idle it was perfect , but as soon as she start making power it would slide open and SFA :D

sorry just my 2 cents

It's not a tunning issue as the engine is completely stock apart from the HKS 2510 turbos. These turbos will flow nearly same air as the stock turbos at the same boost levels so where the problem is won't be effected by this as the air flow is well down from where the fuel/timing maps run out of resolution.

I really can't see where there could be a pipe leak all pipes have been removed and checked, I will defiantly take on board what you have suggested and I will buy new rubber joiners and clamps for the whole system. I guess the only way to really find the leak in on a dyno.

BTW its not a freshly built engine it is a second hand engine with around 70k on the clock.

The newly built engine has to wait till the wifes ute is paid off then RIPZ 3L will be on the way. Funding approved by wife just gotta work my ass off and pay of her ute now.

Cheers for the help guys

It's not a tunning issue as the engine is completely stock apart from the HKS 2510 turbos. These turbos will flow nearly same air as the stock turbos at the same boost levels so where the problem is won't be effected by this as the air flow is well down from where the fuel/timing maps run out of resolution.

I really can't see where there could be a pipe leak all pipes have been removed and checked, I will defiantly take on board what you have suggested and I will buy new rubber joiners and clamps for the whole system. I guess the only way to really find the leak in on a dyno.

BTW its not a freshly built engine it is a second hand engine with around 70k on the clock.

The newly built engine has to wait till the wifes ute is paid off then RIPZ 3L will be on the way. Funding approved by wife just gotta work my ass off and pay of her ute now.

Cheers for the help guys

ok sorry assumed engine had just been fully built (my bad, day dreaming), umm well yes if all youve done is just put the HKS turbos on and it ran fine but then after you flushed your cooler it became a problem then yeah leaning on piping leaking somewhere.

ive tried to show (with red arrows) where mine was leaking, the actual clamp was on and but the hose wasnt actually fully around the lower pipe, and it wasnt visiable cause it was actually on the back side. not sure if you run pods or an air box either but, seeing as i had the air box, when the car was on the dyno there was no way of hearing it actually leaking, so make sure that youve checked it all before putting it on a dyno only to spend 8 hours and finding nothing :P sorry.

good luck

post-1964-1238479646_thumb.jpg

  • 2 weeks later...

Ok so ive started some proper checking before i buy the new rubber joiners tomorrow and i think i found something weird

When the engine starts to cut out im going right off the load side on the fuel map.

afm voltage was hitting past 4v this really dosnt seam normal.

So that tells me it either boost leak(as suspected by alot of people even tho i cant hear anything) or my afm's are f**ked

Have you checked the wastegates to see if there seated?

If there not it won't make boost.

Un plug the hose to the actuator and pump in compressed air (set your compressor to 20psi) and give em blow.

do a compression test mate,

then check base idle postion on the standard computer. also check the position of the crank sensor. make sure its at standard.

check exhaust gaskets on turbos, dumps etc.

all else fails try new set of plugs.

Cheers.

didnt see previous post sorry,

Your airflowmeters are Farked mate, get replacements also check all the wires.

happend to my car as well, i installed Z32s but check the gaksets at the same time turbos, exhaust etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...